Home › Vehicle Interior › AIR CONDITIONING › COMPRESSOR(for 2AZ-FE)
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292186 COMPRESSOR(for 2AZ-FE) A

AIR CONDITIONING  COMPRESSOR(for 2AZ-FE)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the compressor and magnetic clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor and magnetic clutch before installation.

Standard:

(Oil capacity inside the new compressor and magnetic clutch: 130 + 15 cc (4.6 + 0.51 fl.oz.) ) -(Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed from the new compressor when replacing)


NOTICE:
·

When checking the compressor oil level, observe the precautions on the cooler removal/installation.

·

If a new compressor and magnetic clutch is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.

·

If the volume of oil remaining in the removed compressor and magnetic clutch is too small, check for oil leakage.

·

Be sure to use ND-OIL 8 or equivalent for compressor oil.




Hide 88320 2.INSTALL COOLER COMPRESSOR ASSEMBLY

H102250

a.

Install the cooler compressor with the 3 bolts and nut.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration to install the cooler compressor.



Hide 88703 3.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Bracket)

H102249

a.

Install the cooler bracket.


b.

Connect the connector.


c.

Remove the attached vinyl tape from the hose.


d.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

Compressor oil:

ND-OIL 8 or equivalent



e.

Install the O-ring on the cooler refrigerant discharge hose.


f.

Install the cooler refrigerant discharge hose on the cooler compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 7 ft.*lbf)


Hide 88711 4.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/o Bracket)

H102248

a.

Remove the attached vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring on the cooler refrigerant discharge hose.


d.

Install the cooler refrigerant discharge hose on the cooler compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 7 ft.*lbf)


Hide 88712 5.INSTALL NO. 1 COOLER REFRIGERANT SUCTION HOSE

a.
E126966

Remove the attached vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring on the cooler refrigerant suction hose.


d.

Install the cooler refrigerant suction hose on the cooler compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 7 ft.*lbf)


Hide 16361A 6.INSTALL FAN AND GENERATOR V BELT

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 8.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 11.PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.