Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM24M0E _58 Vehicle Interior _059586 ENGINE IMMOBILISER _0292196 ENGINE IMMOBILISER SYSTEM C

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detects errors in its own communications with the ID code box; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the ID code box and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no certification ECU DTCs are present. If present, troubleshoot the certification ECU DTCs first.

DTC No. DTC Detection Condition Trouble Area
B2799 One of following conditions is met:
·

Error in communication between ECM and ID code box

·

Error in communication lines

·

Communication ID is different during communication with ID code box


·

Wire harness

·

ID code box

·

ECM



WIRING DIAGRAM

B144267E08
5.313,2 6.177,2.375 0.865,0.375 10 false G20 0.938,1.99 1.323,2.375 0.385,0.385 10 false A7 ECM 1.281,0.833 1.552,1.042 0.271,0.208 10 false IMI 1.635,0.729 1.823,0.938 0.188,0.208 10 false 11 5.344,0.833 5.708,1.042 0.365,0.208 10 false EFIO 5.125,0.74 5.25,0.906 0.125,0.167 10 false 6 1.24,1.458 1.563,1.667 0.323,0.208 10 false IMO 1.635,1.354 1.854,1.563 0.219,0.208 10 false 10 5.344,1.458 5.656,1.667 0.313,0.208 10 false EFII 5.125,1.365 5.26,1.531 0.135,0.167 10 false 5 5.313,2.167 6.177,2.542 0.865,0.375 10 false ID Code Box

PROCEDURE

1.CHECK FOR DTC

b.

Recheck for the DTC.

OK:

B2799 output does not reoccur.




NG

2.CHECK WIRE HARNESS (ID CODE BOX - ECM)

OK

NORMAL

2.CHECK WIRE HARNESS (ID CODE BOX - ECM)
a.

Disconnect the G20 ID code box connector.


b.

Disconnect the A7 ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G20-5 (EFII) - A7-10 (IMO) Below 1 Ω
G20-6 (EFIO) - A7-11 (IMI)
G20-5 (EFII) or A7-10 (IMO) - Body ground 10 kΩ or higher
G20-6 (EFIO) or A7-11 (IMI) - Body ground




OK

3.REREGISTER ECU CODE REGISTRATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REREGISTER ECU CODE REGISTRATION
a.

Clear the DTC.


b.

Reregister the ID code box and ECM communication ID.


c.

Check that the engine starts.

OK:

Engine starts.




NG

4.CHECK ID CODE BOX (OPERATION)

OK

END (PROBLEM HAS BEEN CAUSED BY REGISTRATION FAILURE)

4.CHECK ID CODE BOX (OPERATION)
a.

Temporarily replace the ID code box with a new or normally functioning one.


b.

Check that the engine starts.

OK:

Engine starts.




OK

END (ID CODE BOX IS DEFECTIVE)

NG

REPLACE ECM