Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM24M0E _58 Vehicle Interior _059586 ENGINE IMMOBILISER _0292196 ENGINE IMMOBILISER SYSTEM C

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is output when the certification ECU does not receive LIN communication signals from the ID code box via LIN for 10 seconds.

DTC No. DTC Detection Condition Trouble Area
B2789 Certification ECU does not receive LIN communication signals from ID code box via LIN for 10 seconds
·

Wire harness

·

ID code box

·

Certification ECU



WIRING DIAGRAM

B144266E04
5.292,2.135 6.375,2.333 1.083,0.198 10 false Certification ECU 0.781,2.156 1.594,2.344 0.813,0.188 10 false ID Code Box 1.25,1.177 1.615,1.385 0.365,0.208 10 false LIN1 1.656,1.031 1.802,1.24 0.146,0.208 10 false 3 5.344,1.188 5.708,1.396 0.365,0.208 10 false LIN 5.073,1.042 5.26,1.208 0.188,0.167 10 false 10 5.281,1.99 5.625,2.198 0.344,0.208 10 false G29 0.771,2 1.083,2.188 0.313,0.188 10 false G20

PROCEDURE

1.CHECK FOR DTC

b.

Recheck for the DTC.

OK:

B2789 output does not reoccur.




NG

2.CHECK WIRE HARNESS (CERTIFICATION ECU - ID CODE BOX)

OK

NORMAL

2.CHECK WIRE HARNESS (CERTIFICATION ECU - ID CODE BOX)
U188584E02
5.438,1.948 5.594,2.24 false 2.74,1.75 3.021,1.198 true 5.417,1.948 5.573,2.24 true 0.104,0.115 1.625,0.323 1.521,0.208 10 false Wire Harness Side: 1.75,1.042 3.052,1.25 1.302,0.208 10 false Certification ECU 5.188,0.969 6.073,1.177 0.885,0.208 10 false ID Code Box 0.146,1.76 0.469,1.958 0.323,0.198 10 false G29 4.427,1.771 4.74,1.969 0.313,0.198 10 false G20 3.063,1.083 3.344,1.281 0.281,0.198 10 false LIN 5.458,2.229 5.927,2.427 0.469,0.198 10 false LIN1

a.

Disconnect the G29 ECU connector.


b.

Disconnect the G20 box connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
LIN (G29-10) - LIN1 (G20-3) Below 1 Ω
LIN (G29-10) or LIN1 (G20-3) - Body ground 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (OPERATION)
a.

Temporarily replace the certification ECU with a new or normally functioning one.


b.

Check for a DTC.

OK:

B2789 is not output.




OK

END (CERTIFICATION ECU IS DEFECTIVE)

NG

REPLACE ID CODE BOX