Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.
| Result | Proceed to |
|---|---|
| Illumination comes on for all components except steering pad switch assembly. | A |
| Illumination comes on for all components except navigation receiver assembly. | B |
| No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.). | C |
A
B
C
(See pageVehicle Interior>LIGHTING>LIGHTING SYSTEM(except LED Headlight)>HOW TO PROCEED WITH TROUBLESHOOTING)
Disconnect the G10 spiral cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G10-12 (IL+2) - Body ground | Light control switch in the tail or head position | 11 to 14 V |
OK
NG
Disconnect the j1 steering pad switch assembly connector.
Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.
Check if the illumination for the steering pad switch assembly comes on.
Illumination for the steering pad switch assembly comes on.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
- | - |
OK
NG
Disconnect the j1 steering pad switch assembly connector.
Disconnect the G10 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| j1-5 (IL+2) - G10-12 (IL+2) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| j1-8 (EAU) - G10-4 (EAU) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| j1-5 (IL+2) - G10-12 (IL+2) | Always | Below 1 Ω |
| j1-8 (EAU) - G10-4 (EAU) | Always | Below 1 Ω |
The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Removal (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL)
Installation (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION)
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
| *b | Steering Pad Switch Assembly Side |
| *c | Vehicle Side |
OK
NG
Disconnect the G10 spiral cable sub-assembly connector.
Disconnect the F17 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G10-4 (EAU) - F17-23 (SWG) | Always | Below 1 Ω |
| G10-4 (EAU) - Body ground | Always | Below 1 Ω |
OK
(See pageAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE)
NG
Disconnect the F13 navigation receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F13-10 (ILL+) - Body ground | Light control switch in the tail or head position | 11 to 14 V |
OK
(See pageAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE)
NG