Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2016.05
RM24M0E _56 Audio / Visual / Telematics _059588 NAVIGATION / MULTI INFO DISPLAY _0292199 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the navigation receiver assembly, perform vehicle contract setting (See page Audio / Visual / Telematics>G-BOOK>G-BOOK SYSTEM>REGISTRATION).


PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop A
Automatic station search function stops on a station B





A

2.CHECK OPTIONAL COMPONENTS

B

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

Result:
Result Proceed to
Optional components are not installed A
Optional components are installed B


NOTICE:

Do not remove optional components without the permission of the customer.




A

3.CHECK NAVIGATION RECEIVER ASSEMBLY

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E187251

Preparation for check

i.

Remove the antenna connector from the navigation receiver assembly.



b.

Check for noise

i.

Turn the engine switch on (ACC) with the navigation receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.





OK

4.CHECK WINDOW GLASS ANTENNA WIRE

NG

4.CHECK WINDOW GLASS ANTENNA WIRE
a.
E111994E14
0.432,0.608 0.620,0.764 0.188,0.156 10 *a 0.946,1.965 1.141,2.114 0.194,0.149 10 *b 2.178,1.735 2.366,1.884 0.188,0.149 10 *c 0.528,0.797 0.602,1.13 false 0.97,1.623 1.044,1.956 false 2.192,1.375 2.266,1.708 false

Check for continuity in the window glass antenna wire.

HINT:

Check for continuity at the center of each antenna wire as shown in the illustration.


NOTICE:

When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.


OK:

There is continuity in the window glass antenna wire.


Text in Illustration
*a Tester Probe
*b Antenna Wire
*c Tin Foil



OK

5.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR WINDOW GLASS ANTENNA WIRE

5.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Disconnect the RA navigation receiver assembly connector.


b.
U111431E01
0.095,0.056 0.274,0.221 0.179,0.165 10 *a 0.624,1.017 0.847,1.180 0.223,0.162 10 RA 0.838,1.477 1.232,1.645 0.393,0.167 10 ANT+ 1.538,1.096 1.136,1.443 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - Body ground Engine switch on (ACC)
Radio switch on and AM or FM selected
11 to 14 V


Text in Illustration
*a Component without harness connected
(Navigation Receiver Assembly)



OK

6.REPLACE ANTENNA CORD SUB-ASSEMBLY

NG

6.REPLACE ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

NORMAL OPERATION

NG

7.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
7.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 2 antenna cord sub-assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

NORMAL OPERATION

NG

8.REPLACE AMPLIFIER ANTENNA ASSEMBLY
8.REPLACE AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

NORMAL OPERATION

NG