Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for RHD) › from 2016.05
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292210 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for RHD) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for RHD)  Clearance Sonar Main Switch Circuit  


DESCRIPTION

The clearance sonar main switch (combination switch assembly) is installed at the base of the driver side of the lower No. 1 instrument panel sub-assembly.

When the clearance sonar main switch (combination switch assembly) is turned on, an on signal is sent to the clearance warning ECU assembly. The Toyota parking assist-sensor system operates according to this signal.

WIRING DIAGRAM

E348211E06
5.531,1.49 6.75,2.052 1.219,0.563 10 false Clearance Warning ECU Assembly 2.24,0.771 3.052,0.979 0.813,0.208 10 false RH ECU-IG 0.406,0.625 2.115,0.823 1.708,0.198 10 false from RH-IG Relay 1 3.281,1.146 5.271,1.563 1.99,0.417 10 false Back Sonar or Clearance Sonar Switch Assembly 5.552,0.635 6.167,0.833 0.615,0.198 10 false CLSW 5.365,0.531 5.583,0.698 0.219,0.167 10 false 9 4.583,0.531 4.802,0.698 0.219,0.167 10 false 3 4.219,0.531 4.573,0.729 0.354,0.198 10 false ECU 3.552,0.531 3.771,0.698 0.219,0.167 10 false IG 3.375,0.531 3.594,0.698 0.219,0.167 10 false 1 5.521,1.302 5.979,1.5 0.458,0.198 10 false G111 3.281,0.979 3.74,1.177 0.458,0.198 10 false G117

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Data List.


e.

According to the display on the GTS, read the Data List.

Clearance Sonar
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Clearance Sonar ECU Clearance warning ECU assembly information/Normal or Abnormal Normal: Clearance warning ECU assembly normal
Abnormal: Clearance warning ECU assembly not normal
-

Result:
Result Proceed to
"Normal" is displayed. A
"Abnormal" is displayed. B




A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Data List.


e.

According to the display on the GTS, read the Data List.

Clearance Sonar
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main Switch Clearance sonar main switch (combination switch assembly )/OFF or ON OFF: Clearance sonar main switch (combination switch assembly) off
ON: Clearance sonar main switch (combination switch assembly) on
-

Result:
Result Proceed to
The display does not change as shown above when the clearance sonar main switch (combination switch assembly) is operated. A
The display changes as shown above when the clearance sonar main switch (combination switch assembly) is operated. B




A

3.INSPECT CLEARANCE SONAR MAIN SWITCH (COMBINATION SWITCH ASSEMBLY)

B

3.INSPECT CLEARANCE SONAR MAIN SWITCH (COMBINATION SWITCH ASSEMBLY)
a.

Remove the clearance sonar main switch (combination switch assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL).


b.
E346520E01
0.088,0.064 0.779,0.498 0.691,0.434 10 *a 2.368,0.379 2.642,0.628 0.274,0.248 10 IG 0.85,0.425 1.411,0.738 0.561,0.313 10 ECU 2.048,1.141 2.246,0.487 false 2.246,0.487 2.34,0.487 false 1.709,1.162 1.425,0.517 false 1.425,0.517 1.27,0.517 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (IG) - 3 (ECU) Clearance sonar main switch (combination switch assembly) on Below 1 Ω
1 (IG) - 3 (ECU) Clearance sonar main switch (combination switch assembly) off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Clearance Sonar Main Switch (Combination Switch Assembly))



OK

4.CHECK HARNESS AND CONNECTOR (CLEARANCE SONAR MAIN SWITCH (COMBINATION SWITCH ASSEMBLY) - BATTERY)

NG

REPLACE CLEARANCE SONAR MAIN SWITCH (COMBINATION SWITCH ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (CLEARANCE SONAR MAIN SWITCH (COMBINATION SWITCH ASSEMBLY) - BATTERY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G117-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V
G117-1 (IG) - Body ground Engine switch off Below 1 V




OK

5.CHECK HARNESS AND CONNECTOR (CLEARANCE SONAR MAIN SWITCH (COMBINATION SWITCH ASSEMBLY) - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CLEARANCE SONAR MAIN SWITCH (COMBINATION SWITCH ASSEMBLY) - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the G111 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G111-9 (CLSW) - G117-3 (ECU) Always Below 1 Ω
G111-9 (CLSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR