Home › Vehicle Interior › WINDOW / GLASS › FRONT SIDE FIX WINDOW GLASS
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292228 FRONT SIDE FIX WINDOW GLASS A

WINDOW / GLASS  FRONT SIDE FIX WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the RH side.



PROCEDURE

Hide 75534 1.REMOVE WINDSHIELD MOULDING OUTSIDE LH

Hide 75546 2.REMOVE WINDSHIELD OUTSIDE MOULDING CLIP

a.

Remove the windshield outside moulding clip (See page Vehicle Interior>EXTERIOR>FRONT PILLAR UPPER COVER>REMOVAL).


Hide 62226 3.REMOVE FRONT PILLAR GARNISH LOWER LH

Hide 62212 4.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

Hide 62212 5.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

Hide 62120B 6.REMOVE FRONT SIDE FIX WINDOW ASSEMBLY LH

B140649E01
0.078,0.225 1.153,0.436 1.075,0.211 10 Protective Tape 1.361,0.345 1.602,0.345 1.602,0.345 1.602,0.651 false

a.

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the quarter window glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.



b.

Using a knife, cut off the moulding as shown in the illustration.

B140650E03
6.333,0.156 5.76,0.156 5.76,0.156 5.76,0.563 false 4.219,2.375 4.729,2.49 4.729,2.49 4.927,2.49 false 1.448,0.198 2.021,0.198 2.021,0.198 2.021,0.604 false 1.49,0.677 1.802,0.917 0.313,0.24 10 false Cut 3.99,1.813 4.302,2.052 0.313,0.24 10 false Cut 6.073,0.615 6.385,0.854 0.313,0.24 10 false Cut 0.823,0.083 1.521,0.292 0.698,0.208 10 false Moulding 5,2.396 5.698,2.604 0.698,0.208 10 false Moulding 6.375,0.073 7.073,0.281 0.698,0.208 10 false Moulding

NOTICE:

Be careful not to damage the vehicle body with the knife.



c.

Remove the remaining moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



d.
B140651E02
1.333,0.385 1.667,0.385 1.667,0.385 1.667,1.094 false 1.208,1.313 1.094,1.313 1.094,1.313 1.094,1.594 false 2.01,1.271 2.01,1.594 2.01,1.594 2.26,1.594 false 2.24,0.708 2.729,0.708 false 0.604,0.292 1.396,0.479 0.792,0.188 10 false Piano Wire 0.99,1.625 1.323,1.813 0.333,0.188 10 false Clip 2.323,1.51 2.656,1.698 0.333,0.188 10 false Clip 2.76,0.625 3.094,0.813 0.333,0.188 10 false Clip

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.




f.

Cut through the adhesive by pulling the piano wire around the glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



g.

Disengage the spacer.


h.

Using suction cups, remove the glass.


Hide 7.CLEAN VEHICLE BODY

B073084E30
2.417,1.396 1.594,0.396 1.594,0.396 0.656,1.49 false 2,1.719 1.635,1.792 1.635,1.792 1.26,1.646 false 1.344,0.177 2.156,0.396 0.813,0.219 10 false Adhesive 1.125,1.813 2.229,2.021 1.104,0.208 10 false Vehicle Body

a.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.