Home › Vehicle Interior › INTERIOR › ROOF HEADLINING › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059596 INTERIOR _0292250 ROOF HEADLINING A

INTERIOR  ROOF HEADLINING  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 67914B 2.REMOVE FRONT DOOR SCUFF PLATE LH

B139941

a.

Using a screwdriver, detach the 10 claws and remove the scuff plate.

HINT:

Tape the screwdriver tip before use.



Hide 67913B 3.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 62112 4.REMOVE COWL SIDE TRIM BOARD LH

B139942

a.

Remove the cap nut.


b.

Using a screwdriver, detach the claw.

HINT:

Tape the screwdriver tip before use.



c.

Using a clip remover, detach the clip and remove the trim board.


Hide 62111C 5.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedures described for the LH side.


Hide 62312C 6.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311C 7.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62226 8.REMOVE FRONT PILLAR GARNISH LOWER LH

B139948

a.

Detach the 7 claws and remove the garnish.


Hide 62225A 9.REMOVE FRONT PILLAR GARNISH LOWER RH

a.

Detach the 7 claws and remove the garnish.


Hide 62212 10.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

a.
B226033

Using a clip remover, detach the 3 clips.


b.

Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.


c.
B139945

Using a clip remover, remove the 4 wire harness clamps.


Hide 62212 11.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

a.
B226034E02
1.104,2.083 1.24,2.25 0.135,0.167 10 false A 1.771,2.646 1.896,2.833 0.125,0.188 10 false B 2.281,3.25 2.417,3.438 0.135,0.188 10 false C 0.635,1.625 0.76,1.813 0.125,0.188 10 false B

Detach the clip labeled A from the vehicle body. Pull the pillar garnish so that the base of the 2 clips labeled B detach. Then pull until the tips of the 2 clips labeled B lock in the pillar garnish's holes.


b.

Using needle-nose pliers, rotate the 2 clips labeled B 90°. Then pull the pillar garnish to release the tips of the 2 clips labeled B from the pillar garnish.


c.

Pull the pillar garnish in the direction indicated by the arrow in the illustration to detach the 2 claws labeled C.


d.

Remove the 2 clips labeled B from the vehicle body.


e.
B139945

Using a clip remover, remove the 4 wire harness clamps.


f.
B460026E01
2.271,2.396 1.365,1.688 1.365,1.688 2.781,1.927 false 1.354,3.51 1.771,3.094 false 1.604,4.073 1.875,3.771 false 2.49,0.521 3.198,0.833 0.708,0.313 10 false 120 mm 0.906,1.094 1.615,1.406 0.708,0.313 10 false 700 mm 0.417,1.573 1.406,1.865 0.99,0.292 10 false Adhesive Tape 0.573,4 1.667,4.271 1.094,0.271 10 false Protective Cover 0.427,3.438 1.417,3.729 0.99,0.292 10 false Adhesive Tape

Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover in place with adhesive tape, as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



Hide 62211 12.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

a.
B226035

Using a clip remover, detach the 3 clips.


b.

Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.


c.
B142591

Disconnect the washer hose.


d.

Remove the bolt and disconnect the ground wire.


e.

Using a clip remover, remove the 4 antenna cord clamps.


Hide 62211 13.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

a.
B226036E02
2.219,2.104 2.365,2.271 0.146,0.167 10 false A 1.563,2.677 1.688,2.844 0.125,0.167 10 false B 1.073,3.271 1.208,3.448 0.135,0.177 10 false C 2.698,1.656 2.823,1.823 0.125,0.167 10 false B

Detach the clip labeled A from the vehicle body. Pull the pillar garnish so that the base of the 2 clips labeled B detach. Then pull until the tips of the 2 clips labeled B lock in the pillar garnish's holes.


b.

Using needle-nose pliers, rotate the 2 clips labeled B 90°. Then pull the pillar garnish to release the tips of the 2 clips labeled B from the pillar garnish.


c.

Pull the pillar garnish in the direction indicated by the arrow in the illustration to detach the 2 claws labeled C.


d.

Remove the 2 clips labeled B from the vehicle body.


e.
B142591

Disconnect the washer hose.


f.

Remove the bolt and disconnect the ground wire.


g.

Using a clip remover, remove the 4 antenna cord clamps.


h.
B131254E01
1.988,1.067 2.607,1.268 0.619,0.201 10 700 mm 0.218,0.473 0.837,0.674 0.619,0.201 10 120 mm 2.009,1.597 3.117,1.798 1.107,0.201 10 Adhesive Tape 2.045,3.489 3.152,3.690 1.107,0.201 10 Adhesive Tape 2.045,4.015 3.294,4.216 1.249,0.201 10 Protective Cover 1.985,3.61 1.715,3.07 false 2.013,4.124 1.621,3.555 false 0.601,1.945 1.947,1.707 1.947,1.707 1.147,2.38 false

Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover in place with adhesive tape, as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



Hide 67918D 14.REMOVE REAR DOOR SCUFF PLATE LH

B139951

a.

Detach the 5 claws and remove the plate.


Hide 67911A 15.REMOVE REAR DOOR SCUFF PLATE RH

a.

Detach the 5 claws and remove the plate.


Hide 67918E 16.REMOVE REAR DOOR SCUFF PLATE LH

B139952

a.

Using a screwdriver, detach the 8 claws.

HINT:

Tape the screwdriver tip before use.



b.

Using a clip remover, detach the 9 clips and remove the scuff plate.


Hide 67917C 17.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 67872A 18.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP LH

Hide 67871E 19.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH

Hide 62414A 20.REMOVE CENTER PILLAR GARNISH LOWER LH

B139953

a.

Disconnect the front seat outer belt's floor anchor.

i.

Remove the anchor cover.


ii.

Remove the bolt and disconnect the floor anchor.



b.

Detach the 2 claws and remove the garnish.


Hide 62413A 21.REMOVE CENTER PILLAR GARNISH LOWER RH

HINT:

Use the same procedures described for the LH side.


Hide 74617A 22.REMOVE ASSIST GRIP PLUG

B139955

a.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip plugs.

HINT:

Tape the screwdriver tip before use.



Hide 74603C 23.REMOVE ASSIST GRIP SUB-ASSEMBLY

a.

Remove the 2 screws and assist grip.


Hide 62412 24.REMOVE CENTER PILLAR GARNISH LH

B139954

a.

Using a clip remover, detach the clip.


b.

Detach the claw and remove the garnish.


Hide 62411 25.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 64420A 26.REMOVE LUGGAGE ROOM BOX LID ASSEMBLY (for Tumble Seat Type, Manual Stowing Seat Type)

Hide 72137E 27.REMOVE NO. 1 SEAT TRACK COVER (for Tumble Seat Type LH Side)

Hide 28.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Tumble Seat Type LH Side)

Hide 72137E 29.REMOVE NO. 1 SEAT TRACK COVER (for Tumble Seat Type RH Side)

Hide 30.REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Tumble Seat Type RH Side)

Hide 79236B 31.REMOVE NO. 2 SEAT LEG COVER LH (for Power Stowing Seat Type LH Side)

Hide 79384 32.REMOVE NO. 3 SEAT LEG COVER REAR LH (for Power Stowing Seat Type LH Side)

Hide 79273A 33.REMOVE NO. 2 SEAT HINGE COVER (for Power Stowing Seat Type LH Side)

Hide 34.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Power Stowing Seat Type LH Side)

Hide 79040 35.REMOVE NO. 3 SEAT LEG ASSEMBLY LH (for Power Stowing Seat Type LH Side)

Hide 79236A 36.REMOVE NO. 2 SEAT LEG COVER (for Power Stowing Seat Type RH Side)

Hide 79374 37.REMOVE NO. 3 SEAT LEG COVER REAR RH (for Power Stowing Seat Type RH Side)

Hide 79273 38.REMOVE NO. 2 SEAT HINGE COVER (for Power Stowing Seat Type RH Side)

Hide 39.REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Power Stowing Seat Type RH Side)

Hide 79030 40.REMOVE NO. 3 SEAT LEG ASSEMBLY RH (for Power Stowing Seat Type RH Side)

Hide 79384 41.REMOVE NO. 3 SEAT LEG COVER REAR LH (for Manual Stowing Seat Type LH Side)

Hide 79236B 42.REMOVE NO. 2 SEAT LEG COVER LH (for Manual Stowing Seat Type LH Side)

Hide 79236A 43.REMOVE NO. 2 SEAT LEG COVER (for Manual Stowing Seat Type LH Side)

Hide 79273A 44.REMOVE NO. 2 SEAT HINGE COVER (for Manual Stowing Seat Type LH Side)

Hide 45.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Manual Stowing Seat Type LH Side)

Hide 72906 46.REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH (for Manual Stowing Seat Type LH Side)

Hide 79374 47.REMOVE NO. 3 SEAT LEG COVER REAR RH (for Manual Stowing Seat Type RH Side)

Hide 79236B 48.REMOVE NO. 2 SEAT LEG COVER LH (for Manual Stowing Seat Type RH Side)

Hide 79236A 49.REMOVE NO. 2 SEAT LEG COVER (for Manual Stowing Seat Type RH Side)

Hide 79273A 50.REMOVE NO. 2 SEAT HINGE COVER (for Manual Stowing Seat Type RH Side)

Hide 51.REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Manual Stowing Seat Type RH Side)

Hide 72905 52.REMOVE 3RD SEAT LINK SUB-ASSEMBLY RH (for Manual Stowing Seat Type RH Side)

Hide 67881A 53.REMOVE BACK DOOR WEATHERSTRIP

Hide 67935 54.REMOVE BACK DOOR SCUFF PLATE

B139958

a.

Using a clip remover, remove the 6 clips.


b.

Using a clip remover, detach the 6 clips.


c.

Detach the 4 claws and remove the scuff plate.


Hide 67939D 55.REMOVE BACK DOOR GARNISH CENTER (for Manual Stowing Seat Type, Power Stowing Seat Type)

a.
B462717

for Type A:

i.

Using a screwdriver, detach the 8 claws and remove the garnish.

HINT:

Tape the screwdriver tip before use.




b.
B320320

for Type B:

i.

Using a screwdriver, detach the 6 claws and remove the garnish.

HINT:

Tape the screwdriver tip before use.




Hide 58625D 56.REMOVE REAR FLOOR NO. 1 MAT PLATE (for Tumble Seat Type, Manual Stowing Seat Type)

B139956

a.

Using a screwdriver, detach the 6 claws.

HINT:

Tape the screwdriver tip before use.



b.

Using a clip remover, detach the 5 clips and remove the plate.


Hide 58625D 57.REMOVE REAR FLOOR NO. 1 MAT PLATE (for Power Stowing Seat Type)

B139957

a.

Using a screwdriver, detach the 6 claws.

HINT:

Tape the screwdriver tip before use.



b.

Using a clip remover, detach the 9 clips and remove the plate.


Hide 66311B 58.REMOVE ROPE HOOK

B142592

a.

Using a screwdriver, detach the 2 claws of the cover.

HINT:

Tape the screwdriver tip before use.



b.

Remove the bolt and hook.


Hide 64735G 59.REMOVE DECK TRIM SIDE SERVICE HOLE COVER LH

B142593

a.

Detach the 7 claws and remove the cover.


Hide 64735F 60.REMOVE DECK TRIM SIDE SERVICE HOLE COVER RH

a.

Detach the 7 claws and remove the cover.


Hide 64766 61.REMOVE QUARTER TRIM JACK COVER SUB-ASSEMBLY (for LH Side)

B142594

a.

Using a screwdriver, detach the 9 claws and remove the cover.

HINT:

Tape the screwdriver tip before use.



Hide 64740A 62.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Captain Seat Type)

B139959

a.

Disconnect the rear No. 2 seat outer belt's floor anchor.

i.

Remove the bolt and disconnect the floor anchor.



b.

Remove the screw.


c.

Using a clip remover, remove the 4 clips.


d.

Using a screwdriver, detach the 8 claws.

HINT:

Tape the screwdriver tip before use.



e.

Using a clip remover, detach the 12 clips and remove the trim board.


f.

for Power Stowing Seat Type:

i.

Disconnect the fold seat switch connector.



Hide 64740A 63.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Except Captain Seat Type)

B139959

a.

Disconnect the rear No. 1 seat outer belt's floor anchor.

i.

Remove the bolt and disconnect the floor anchor.



b.

Disconnect the rear No. 2 seat outer belt's floor anchor.

i.

Remove the bolt and disconnect the floor anchor.



c.

Remove the screw.


d.

Using a clip remover, remove the 4 clips.


e.

Using a screwdriver, detach the 8 claws.

HINT:

Tape the screwdriver tip before use.



f.

Using a clip remover, detach the 12 clips and remove the trim board.


Hide 64730B 64.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for Captain Seat Type)

B139960

a.

Disconnect the rear No. 2 seat outer belt's floor anchor.

i.

Remove the bolt and disconnect the floor anchor.



b.

Remove the screw.


c.

Using a clip remover, remove the 2 clips.


d.

Using a screwdriver, detach the 8 claws.

HINT:

Tape the screwdriver tip before use.



e.

Using a clip remover, detach the 12 clips and remove the trim board.


f.

Disconnect the 3 connectors.


Hide 64730B 65.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for Except Captain Seat Type)

B139960

a.

Disconnect the rear No. 1 seat outer belt's floor anchor.

i.

Remove the bolt and disconnect the floor anchor.



b.

Disconnect the rear No. 2 seat outer belt's floor anchor.

i.

Remove the bolt and disconnect the floor anchor.



c.

Remove the screw.


d.

Using a clip remover, remove the 2 clips.


e.

Using a screwdriver, detach the 8 claws.

HINT:

Tape the screwdriver tip before use.



f.

Using a clip remover, detach the 12 clips and remove the trim board.


g.

Disconnect the 3 connectors.


Hide 62639A 66.REMOVE QUARTER PILLAR GARNISH LH (for Captain Seat Type)

B139962

a.

Using a clip remover, detach the clip.


b.

Detach the claw and remove the garnish.


Hide 62639A 67.REMOVE QUARTER PILLAR GARNISH LH (for Except Captain Seat Type)

B139961

a.

Using a clip remover, detach the clip.


b.

Disconnect the rear No. 1 seat outer belt's shoulder anchor.


c.

Detach the claw and remove the garnish.


Hide 62638A 68.REMOVE QUARTER PILLAR GARNISH RH (for Captain Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 62638A 69.REMOVE QUARTER PILLAR GARNISH RH (for Except Captain Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 62472A 70.REMOVE INNER ROOF SIDE GARNISH LH

B139963

a.

Disconnect the rear No. 2 seat outer belt's shoulder anchor.

i.

Using a screwdriver, detach the 2 claws and open the seat belt anchor cover.

HINT:

Tape the screwdriver tip before use.



ii.

Remove the bolt and disconnect the shoulder anchor.



b.

Using a clip remover, detach the 3 clips.


c.

Detach the 2 claws and remove the garnish.


Hide 62471A 71.REMOVE INNER ROOF SIDE GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62452C 72.REMOVE REAR ROOF SIDE RAIL GARNISH LH

B139964

a.

Using a clip remover, detach the 4 clips.


b.

Detach the 6 claws and remove the garnish.


Hide 62451C 73.REMOVE REAR ROOF SIDE RAIL GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 88566A 74.REMOVE NO. 1 COOLER AIR DUCT

B142595

a.

Detach the 2 claws and remove the plate.


b.

Remove the air duct.


Hide 73139B 75.REMOVE SEAT BELT ANCHOR COVER

B139966

a.

Using a clip remover, detach the 4 clips.


b.

Detach the 6 claws and remove the cover.


Hide 74320 76.REMOVE VISOR ASSEMBLY LH

a.
B131005

Using a screwdriver, detach the 4 claws and remove the visor bracket cover.

HINT:

Tape the screwdriver tip before use.



b.
B131006E02
1.948,1.75 2.104,1.927 0.156,0.177 10 false A

Remove portion A from the visor holder.


c.

Detach the 2 claws and remove the visor.


Hide 74310 77.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 74348 78.REMOVE VISOR HOLDER

B147254

a.

Rotate the tip of the visor holder and pull it out downward.


b.

Using a screwdriver, detach the 2 claws and remove the holder.

HINT:

Tape the screwdriver tip before use.



Hide 87820A 79.REMOVE INNER REAR CONVERSATION MIRROR ASSEMBLY

Hide 81260A 80.REMOVE MAP LIGHT ASSEMBLY

Hide 84010A 81.REMOVE COOLER CONTROL SWITCH SUB-ASSEMBLY

Hide 86295 82.REMOVE TELEVISION BASE (w/ Television Display)

Hide 86680A 83.REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Television Display)

Hide 74612 84.REMOVE ASSIST GRIP COVER

HINT:

Use the same procedure for the other assist grip cover.


B131002

a.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.



Hide 74610A 85.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for the other assist grip.


B131003

a.

Detach the 4 claws and remove the assist grip.


Hide 63310 86.REMOVE ROOF HEADLINING ASSEMBLY

a.
B142596

Disconnect the 6 roof wire connectors.


b.
B142597

Disconnect the washer hose.


c.
B142599

Disconnect the antenna cord connector from the front pillar RH.


d.
B142598

Disconnect the antenna cord connector from the rear pillar RH.


e.
B460054E01
0.167,0.052 1.708,0.323 1.542,0.271 10 false w/o Sliding Roof: 0.167,2.427 1.708,2.698 1.542,0.271 10 false w/ Sliding Roof:

Using a clip remover, detach the 2 clips.


f.

Detach the hooks and remove the headlining.


Hide 81250 87.REMOVE ROOM NO. 2 LIGHT ASSEMBLY

Hide 81290 88.REMOVE ROOM NO. 3 LIGHT ASSEMBLY

Hide 81340 89.REMOVE VANITY LIGHT ASSEMBLY

Hide 86101 91.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

Hide 82171 92.REMOVE ROOF NO. 1 WIRE

B460041E01
0.135,0.063 1.594,0.344 1.458,0.281 10 false w/o Sliding Roof: 0.146,2.531 1.604,2.813 1.458,0.281 10 false w/ Sliding Roof:

a.

Only when replacing the roof headlining:


b.

Remove the washer hose.


c.

w/o Sliding Roof:

i.

Detach the 7 wire harness clamps and remove the tape.


ii.

Remove the double-sided tape and roof wire.



d.

w/ Sliding Roof:

i.

Detach the 21 wire harness clamps and remove the tape.


ii.

Remove the double-sided tape and roof wire.



Hide 63341 93.REMOVE ROOF NO. 1 SILENCER PAD (w/o Sliding Roof)

a.

Remove the silencer pad.


Hide 63342 94.REMOVE ROOF NO. 2 SILENCER PAD (w/o Sliding Roof)

a.

Remove the 3 silencer pads.


Hide 95.REMOVE FASTENER HOOK (w/o Sliding Roof)

a.

Remove the 7 hooks.