Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2013.04–2016.05
RM24M0E _56 Audio / Visual / Telematics _059588 NAVIGATION / MULTI INFO DISPLAY _0292199 NAVIGATION SYSTEM Y

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the navigation system.

·

*: Use the intelligent tester.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
·

When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points in problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

4.CHECK CABIN
4.CHECK CABIN
a.

Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.

OK:

Condensation is not likely being produced and the temperature is not high or extremely low.


HINT:
·

A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.

·

The navigation system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.




Result:
Proceed to
OK
NG



OK

5.CHECK NAVIGATION SYSTEM NORMAL CONDITION

NG

SET CABIN TO APPROPRIATE TEMPERATURE

5.CHECK NAVIGATION SYSTEM NORMAL CONDITION
a.

Refer to Check System Normal Condition (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK).

Result:
Result Proceed to
Symptom is not normal operation. A
Symptom is normal operation. B




A

6.CHECK CAN COMMUNICATION SYSTEM*

B

SYMPTOM IS NORMAL OPERATION

6.CHECK CAN COMMUNICATION SYSTEM*
a.

Check for DTC output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result:
Result Proceed to
CAN DTCs are not output. A
CAN DTCs are output. B




A

7.CHECK FOR DTC*

B

7.CHECK FOR DTC*
a.

Refer to DTC Check/Clear (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B


HINT:

If the system cannot enter diagnostic mode, inspect the AVC-LAN and all the components that connect to the AVC-LAN for short circuits and repair or replace the problem part (w/ Rear Seat Entertainment System) (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>AVC-LAN Circuit).




A

8.DTC CLEAR*

B

11.PROBLEM SYMPTOMS TABLE
8.DTC CLEAR*
a.

Refer to DTC Check/Clear (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

HINT:

The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.



Result:
Proceed to
NEXT



NEXT

9.RECHECK FOR DTC*
9.RECHECK FOR DTC*
a.

Refer to DTC Check/Clear (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B


HINT:
·

Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.

·

If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the intelligent tester.

·

Check the DTCs and inspect the area that the code indicates.





A

10.DIAGNOSTIC TROUBLE CODE CHART

B

11.PROBLEM SYMPTOMS TABLE
10.DIAGNOSTIC TROUBLE CODE CHART

Result:
Proceed to
NEXT



NEXT

13.CHECK CIRCUIT
11.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE).

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).




A

12.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

B

13.CHECK CIRCUIT
12.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

Result:
Proceed to
NEXT



NEXT

13.CHECK CIRCUIT
13.CHECK CIRCUIT
a.

Adjust, repair or replace as necessary.


Result:
Proceed to
NEXT



NEXT

14.RECHECK FOR DTC*
14.RECHECK FOR DTC*

Result:
Proceed to
NEXT



NEXT

15.PERFORM CONFIRMATION TEST
15.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END