Home › Audio / Visual / Telematics › G-BOOK › G-BOOK SYSTEM › 2013.04–2016.05
RM24M0E _56 Audio / Visual / Telematics _059589 G-BOOK _0292202 G-BOOK SYSTEM Y

G-BOOK  G-BOOK SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the G-BOOK system.

·

*: Use the intelligent tester.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CHECK PROBLEM SYMPTOM
2.CHECK PROBLEM SYMPTOM
a.

The G-BOOK system provides a variety of functions. Therefore, it is important to identify whether a malfunction is related to the communication system, including radio wave conditions, or any other systems. Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal condition caused the malfunction.

Displayed Message and Problem Symptom Cause
A message is displayed temporarily indicating to try again after moving the vehicle because the center cannot be accessed, as the screen cannot be displayed due to a busy line, etc. This is caused when there is a problem with the radio wave signal conditions or when the base station is busy. This is not a malfunction (inform the customer that this is not a malfunction and ask them to use the system as is).
A message is displayed temporarily indicating to try again after waiting for a while because the information cannot be retrieved due to a busy line, etc. This is caused when there is a problem with the radio wave signal conditions or when the base station is busy. This is not a malfunction (inform the customer that this is not a malfunction and ask them to use the system as is).
A message is displayed temporarily indicating to try again after waiting for a while because the lines are busy. This is caused when there is a problem with the radio wave signal conditions or when the base station is busy. This is not a malfunction (inform the customer that this is not a malfunctions and ask them to use the system as is).


Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the intelligent tester to check if the CAN communication system is functioning normally (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B




A

5.PROBLEM SYMPTOMS TABLE

B

5.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table (See page Audio / Visual / Telematics>G-BOOK>G-BOOK SYSTEM>PROBLEM SYMPTOMS TABLE).

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).




A

6.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

B

7.CHECK CIRCUIT
6.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

Result:
Proceed to
NEXT



NEXT

7.CHECK CIRCUIT
7.CHECK CIRCUIT
a.

Adjust, repair or replace as necessary.

NOTICE:

If the navigation receiver assembly is replaced, perform the vehicle contract setting (See page Audio / Visual / Telematics>G-BOOK>G-BOOK SYSTEM>REGISTRATION).



Result:
Proceed to
NEXT



NEXT

8.PERFORM CONFIRMATION TEST
8.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END