When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2284 | The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN information is inconsistent | ·
Stop light switch ·
CAN communication system ·
ECM ·
Instrument panel junction block LH (Main body ECU) ·
Wire harness or connector |
EMERGENCY ENGINE START CONTROL
If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU. This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.
To activate the starter:
Turn the engine switch from off to on (ACC).
Press and hold the engine switch for 15 seconds.
Before performing the inspection, depress the brake pedal and check that the stop lights come on. If the stop lights do not come on when the brake pedal is depressed, refer to the page shown in the brackets.
for LED Headlight: Click hereVehicle Interior>LIGHTING>LIGHTING SYSTEM(for LED Headlight)>PROBLEM SYMPTOMS TABLE
for except LED Headlight: Click hereVehicle Interior>LIGHTING>LIGHTING SYSTEM(except LED Headlight)>PROBLEM SYMPTOMS TABLE
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Check the DATA LIST for proper functioning of the stop light switch.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch/ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.
OK
NG
Delete the DTCs (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>DATA LIST / ACTIVE TEST).
Check for CAN communication system DTCs (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
No DTC is output.
OK
NG
(See pagePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Delete the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Check for DTC P0500 (Vehicle speed sensor A) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0500).
No DTC is output.
OK
NG
Remove the STOP fuse from the instrument panel junction block RH.
Measure the resistance of the fuse.
Below 1 Ω
OK
NG
Disconnect the A33 switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-2 - Body ground | Always | 11 to 14 V |
OK
NG
Remove the stop light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Switch pin free | Below 1 Ω |
| 3 - 4 | Switch pin free | 10 kΩ or higher |
| 1 - 2 | Switch pin pushed in | 10 kΩ or higher |
| 3 - 4 | Switch pin pushed in | Below 1 Ω |
OK
NG
Disconnect 4K connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-1 - 4K-7 | Always | Below 1 Ω |
| A33-1 - Body ground | 11 kΩ or higher |
OK
NG