Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



A115899E21
0.766,1.047 1.553,1.425 0.787,0.378 10 from Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.498,1.96 5.333,2.123 1.835,0.163 10 Combination Meter Assembly 3.113,0.599 3.921,0.776 0.809,0.177 10 4-Pulse 5.039,0.599 5.848,0.776 0.809,0.177 10 4-Pulse 6.068,1.841 6.515,2.004 0.448,0.163 10 ECM

DTC No. DTC Detection Condition Trouble Area
P0500 While vehicle being driven, no vehicle speed sensor signal to ECM (1 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

Skid control ECU

·

ECM



WIRING DIAGRAM

A127263E02
0.543,1.793 1.714,1.957 1.170,0.164 10 Skid Control ECU 2.191,0.81 4.094,1.020 1.904,0.210 10 Combination Meter Assembly 2.441,1.682 2.597,1.863 0.156,0.181 10 SI 2.147,1.696 2.323,1.839 0.176,0.143 10 39 2.191,0.652 2.476,0.795 0.285,0.143 10 G28 3.919,1.696 4.095,1.839 0.176,0.143 10 40 5.061,1.696 5.164,1.839 0.103,0.143 10 8 3.626,1.682 3.816,1.863 0.191,0.181 10 +S 5.874,0.838 6.200,0.977 0.326,0.139 10 ECM 5.664,0.838 5.853,0.988 0.189,0.150 10 A7 5.233,1.646 5.535,1.827 0.303,0.181 10 SPD 5.991,1.336 6.295,1.496 0.304,0.160 10 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in speedometer malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

NG

GO TO MALFUNCTION IN SPEEDOMETER

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Vehicle Speed.


d.

Drive the vehicle.


e.

Read the value displayed on the tester.

OK:

Vehicle speeds displayed on tester and speedometer display are equal.




OK

NG

3.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
3.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
a.
U188517E01
0.077,0.051 1.334,0.261 1.257,0.210 10 Wire Harness Side 1.678,4.251 2.537,4.400 0.859,0.149 10 Turn Wheel 0.057,2.706 0.675,2.855 0.618,0.149 10 5 to 12 V 0.32,4.125 0.578,4.274 0.257,0.149 10 0 V 0.561,1.998 0.814,2.147 0.253,0.149 10 +S 0.838,1.449 0.673,1.952 false 0.871,0.537 2.767,0.747 1.896,0.210 10 Combination Meter Connector 0.392,0.534 0.713,0.697 0.320,0.163 10 G28

Shift the transmission gear selector lever to the neutral position.


b.

Jack up the vehicle.


c.

Turn the engine switch on (IG).


d.

Measure the voltage between the terminal of the combination meter assembly and the body ground while the front wheel is turned slowly.

Standard Voltage:
Tester Connection Specified Condition
G28-40 (+S) - Body ground Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (check for open):
Tester Connection Condition Specified Condition
G28-40 (+S) - A7-8 (SPD) Always Below 1 Ω


Standard Resistance (check for short):
Tester Connection Condition Specified Condition
G28-40 (+S) or A7-8 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR