DATA LIST / ACTIVE TEST
System information · Vehicles built Nov 2010 – Jul 2011
Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are for reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Actual vehicle speed
The speed is indicated on speedometer.
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
650 to 750 rpm: Idling
-
Calculate Load
Calculated load by ECM/
Min.: 0%, Max.: 100%
- 10 to 40%: Idling
- 10 to 40%: Running without load (2500 rpm)
-
Vehicle Load
Vehicle load/
Min.: 0%, Max.: 25700%
Actual vehicle load
-
MAF
Air flow rate from Mass Air Flow (MAF) meter/
Min.: 0 gm/sec., Max.: 655.35 gm/sec.
2.5 to 4.7 gm/sec: Idling
8.0 to 18.9 gm/sec: 2500 rpm
If the mass air flow volume is approximately 0.0 gm/sec.: - The mass air flow meter power source circuit is open or short.
- The VG circuit is open or short.
- The E2G circuit is open.
Atmosphere Pressure
Atmospheric pressure/
Min.: 0 kPa, Max.: 255 kPa
Equivalent to atmospheric pressure
(absolute pressure)
-
Coolant Temp
Engine coolant temperature/
Min.: -40°C, Max.: 140°C
80 to 100°C (176 to 212°F): After warming up
If the value is -40°C (-40°F): the sensor circuit is open.
If the value is 140°C (284°F): the sensor circuit is shorted.
Intake Air
Intake air temperature/
Min.: -40°C, Max.: 140°C
Equivalent to ambient air temperature
If the value is -40°C (-40°F): the sensor circuit is open.
If the value is 140°C (284°F): the sensor circuit is shorted.
Engine Run Time
Engine run time/
Min.: 0 s, Max.: 65535 s
Time after engine start
Service data.
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C, Max.: 119.3°C
Coolant temperature when engine started
Service data.
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C, Max.: 119.3°C
Intake air temperature when engine started
Service data.
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 14 V: Idling
-
Accelerator Position
Accelerator pedal position/
Min.: 0%, Max.: 399.9%
Actual accelerator pedal position
-
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1/
Min.: 0%, Max.: 100%
10 to 22%: accelerator pedal released
54 to 86%: accelerator pedal fully depressed
-
Accel Sens. No.2 Volt %
Absolute APP No. 2/
Min.: 0%, Max.: 100%
12 to 42%: accelerator pedal released
66 to 98%: accelerator pedal fully depressed
-
Accel Sensor Out No.1
APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.980 V
-
ETCS service data Normal: Fixed at 0.000 V
Accel Sensor Out No.2
APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.980 V
-
ETCS service data Normal: Fixed at 0.000 V
Accel Sensor Out No.1
APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.980 V
0.5 to 1.1 V: accelerator pedal released
2.6 to 4.5 V: accelerator pedal fully depressed
-
Accel Sensor Out No.2
APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.980 V
1.2 to 2.0 V: accelerator pedal released
3.4 to 5.0 V: accelerator pedal fully depressed
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
ON: Idling
-
Accel Fully Close Learn #1
Accelerator fully closed learning value No. 1/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data.
Accel Fully Close Learn #2
Accelerator fully closed learning value No. 2/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data.
Throttle Sensor Volt %
Throttle valve opening percentage according to throttle position sensor/
Min.: 0%, Max.: 100%
- 10 to 22%: Accelerator pedal released
- 64 to 96%: Accelerator pedal fully depressed
Value calculated based on the voltage at terminal VTA1.
Throttl Sensor #2 Volt %
Throttle valve opening percentage according to throttle position sensor No. 2/
Min.: 0%, Max.: 100%
- 42 to 62%: Accelerator pedal released
- 92 to 100%: Accelerator pedal fully depressed
Value calculated based on the voltage at terminal VTA2.
ST1
Brake pedal signal/
ON or OFF
ON: Brake pedal depressed
-
System Guard
System guard/
ON or OFF
-
ETCS service data.
Open Side Malfunction
Open side malfunction/
ON or OFF
-
ETCS service data.
Throttle Idle Position
Whether or not throttle position sensor detecting idling
ON or OFF
- ON: Accelerator pedal released
- OFF: Accelerator pedal fully depressed
-
Throttle Require Position
Required throttle position/
Min.: 0 V, Max.: 4.980 V
0.5 to 1.1 V: Idling
-
Throttle Sensor Position*1
Throttle position sensor/
Min.: 0%, Max.: 100%
- 0%: Accelerator pedal released
- 50 to 80%: Accelerator pedal fully depressed
Recognition value for throttle opening angle on ECM.
Throttle Position No. 1
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.980 V
-
ETCS service data Normal: Fixed at 0.000 V
Throttle Position No. 2
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.980 V
-
ETCS service data Normal: Fixed at 0.000 V
Throttle Position No. 1
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.980 V
- 0.5 to 1.1 V: Accelerator pedal released
- 3.2 to 4.8 V: Accelerator pedal fully depressed
- 0.6 to 1.4 V: Fail-safe operating
-
Throttle Position No. 2
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.980 V
- 2.1 to 3.1 V: Accelerator pedal released
- 4.6 to 5.0 V: Accelerator pedal fully depressed
- 2.1 to 3.1 V: Fail-safe operating
-
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.980 V
0.5 to 4.8 V
-
Throttle Sens Open Pos #1
Throttle sensor opener position No. 1/
Min.: 0 V, Max.: 4.980 V
0.6 to 1.4 V
ETCS service data.
Throttle Sens Open Pos #2
Throttle sensor opener position No. 2/
Min.: 0 V, Max.: 4.980 V
1.7 to 2.5 V
ETCS service data.
Throttle Motor Current
Throttle motor current/
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling
ETCS service data.
Throttle Motor DUTY
Throttle actuator/
Min.: 0%, Max.: 100%
10 to 22%: Idling after engine warmed up
ETCS service data.
Throttle Motor Current
Throttle actuator current/
Min.: 0 A, Max.: 19.92 A
0 to 3.0 A: Idling
ETCS service data.
Throttle Motor Open Duty
Throttle actuator open duty ratio/
Min.: 0%, Max.: 100%
-
ETCS service data.
Throttle Motor Close Duty
Throttle actuator closed duty ratio/
Min.: 0%, Max.: 100%
-
ETCS service data.
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
ETCS service data.
Throttle Motor Duty (Close)
Throttle actuator duty ratio (closed)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
ETCS service data.
Throttle Fully Close Learn
Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.980 V
0.4 to 1.0 V: Accelerator pedal released
-
+BM Voltage
+BM voltage/
Min.: 0 V, Max.: 79.998 V
11 to 14 V: Ignition switch ON and system normal
ETCS service data.
Actuator Power Supply
Actuator power supply/
ON or OFF
ON: Idling
ETCS service data.
Throttle Position
Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
-
For use when engine stall, starting problems or rough idle is present.
ISC Flow
Flow rate calculated using information from each sensor/
Min.: 0 L/s, Max.: 79.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
ISC Position
Requested opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
-
For use when engine stall, starting problems or rough idle is present.
ISC Feedback Value
ISC feedback compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
ISC Learning Value
ISC learned compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val
Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val
Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
PS Feedback Val
Power steering load feedback value: Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Low Revolution Control
Low engine speed control operation state/
ON or OFF
-
For use when engine stall, starting problems or rough idle is present.
Neutral Control
Status of low engine speed control/
ON or OFF
-
For use when engine stall, starting problems or rough idle is present.
N Range Status*3
Shift lever N status/
ON or OFF
-
For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow
Intake air compensation flow rate/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Deposit Loss Flow
Flow loss due to deposits/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Injector (Port)
Injection period of the No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
1600 to 2700 μs: idling
-
Injection Volum (Cylinder 1)
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.5 ml
Quantity of fuel injection volume for 10 times.
Fuel Pump/Speed Status
Fuel pump/speed status/
ON or OFF
-
Active Test support data.
Current Fuel Type
Current fuel type
-
Identifying the current fuel type:
Gasoline
EVAP (Purge) VSV
Purge VSV control duty/
Min.: 0%, Max.: 100%
0 to 100%: During idling
Order signal from ECM.
Evap Purge Flow
Purge flow/
Min.: 0%, Max.: 399.9%
0 to 100%: Idling
-
Purge Density Learn Value
Learning value of purge density/
Min.: -200%, Max.: 199.993%
-40 to 0%: Idling
Service data.
Vapor pressure (calculated)
Calculated EVAP system pressure/
Min.: -720.896 kPa, Max.: 720.874 kPa
Approximately 100 kPa: Ignition switch ON
-
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
-
Active Test support data.
Purge Cut VSV Duty
Purge cut VSV duty/
Min.: 0%, Max.: 399.9%
-
-
Target Air-Fuel Ratio
Air fuel ratio:
Min.: 0, Max.: 1.999
0.8 to 1.2: During idling
-
AF Lambda B1S1
Short-term fuel trim associated with the Bank 1 Sensor 1/
Min.: 0, Max.: 1.999
- Value less than 1 (0.000 to 0.999) = Rich
- Stoichiometric air fuel ratio = 1
- Value more than 1 (1.001 to 1.999) = Lean
-
AF Lambda B2S1
Short-term fuel trim associated with the Bank 2 Sensor 1/
Min.: 0, Max.: 1.999
- Value less than 1 (0.000 to 0.999) = Rich
- Stoichiometric air fuel ratio = 1
- Value more than 1 (1.001 to 1.999) = Lean
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
AFS Voltage B2S1
Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
AFS Current B1S1
Air fuel ratio sensor current Bank 1 Sensor 1/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
AFS Current B2S1
Air fuel ratio sensor current (for Bank 2 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
A/F Heater Duty #1
A/F heater duty ratio (for Bank 1)
Min.: 0%, Max.: 399.9%
0 to 100 %
-
A/F Heater Duty #2
A/F heater duty ratio (for Bank 2)
Min.: 0%, Max.: 399.9%
0 to 100 %
-
O2S B1S2
Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
O2S B2S2
Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
O2S Impedance B1S2
Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/
Min.: 0 ohm, Max.: 21247.67 ohm
5 to 15000 ohm
-
O2S Impedance B2S2
Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/
Min.: 0 ohm, Max.: 21247.67 ohm
5 to 15000 ohm
-
O2 Heater B1S2
Heated oxygen sensor heater for bank 1 sensor 2/
Not Act or Active
-
-
O2 Heater B2S2
Heated oxygen sensor heater for bank 2 sensor 2/
Not Act or Active
-
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current for bank 1 sensor 2/
Min.: 0 A, Max.: 4.9 A
-
-
O2 Heater Curr Val B2S2
Heated oxygen sensor current for bank 2 sensor 2/
Min.: 0 A, Max.: 4.9 A
-
-
Short FT #1
Short-term fuel trim of Bank 1/
Min.: -100%, Max.: 99.200%
-20 to 20%
This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
Long FT #1
Long-term fuel trim of Bank 1/
Min.: -100%, Max.: 99.200%
-20 to 20%
This item refers to the overall fuel compensation carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #1
Total fuel trim of Bank 1
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
-
Short FT #2
Short-term fuel trim of Bank 2/
Min.: -100%, Max.: 99.200%
-20 to 20%
This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
Long FT #2
Long-term fuel trim of Bank 2/
Min.: -100%, Max.: 99.200%
-20 to 20%
This item refers to the overall fuel compensation carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #2
Total fuel trim of Bank 2
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
-
Fuel System Status #1
Fuel system status (Bank 1)/
OL, CL, OLDrive, OLFault or CLFault
CL: Idling after warming up
- OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
- CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
- OLDrive: Open loop due to driving conditions (fuel enrichment).
- OLFault: Open loop due to a detected system fault.
- CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (Bank 2)/
OL, CL, OLDrive, OLFault or CLFault
CL: Idling after warming up
- OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
- CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
- OLDrive: Open loop due to driving conditions (fuel enrichment).
- OLFault: Open loop due to a detected system fault.
- CLFault: Closed loop but the air fuel ration sensor, which is used for fuel control, is malfunctioning.
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg, Max.: 63.5 deg
BTDC 7 to 24°: Idling
-
Knock Feedback Value
Feedback value of knocking/
Min.: -1024°CA, Max.: 1023.9°CA
-22 to 0° CA:
Driving, 70 km/h (44 mph)
Service data.
Knock Correct Learn Value
Correction learning value of knocking/
Min.: -1024°CA, Max.: 1023.9°CA
0 to 22° CA:
Driving, 70 km/h (44 mph)
Service data.
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)/
Min.: 0° CA, Max.: 15.93° CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)/
Min.: 0° CA, Max.: 15.93° CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)/
Min.: 0° CA, Max.: 15.93° CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)/
Min.: 0° CA, Max.: 15.93° CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #5
Individual cylinder timing advance compensation amount (No. 5)/
Min.: 0° CA, Max.: 15.93° CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #6
Individual cylinder timing advance compensation amount (No. 6)/
Min.: 0° CA, Max.: 15.93° CA
-
For use when engine stall, starting problems or rough idle is present.
VVT Control Status #1
Variable valve timing (VVT) control status (Bank 1)/
ON or OFF
-
Active Test support data.
VVT Control Status #2
VVT control status (Bank 2)/
ON or OFF
-
Active Test support data.
VVT Advance Fail
VVT control failure status/
ON or OFF
ON: VVT control failure
-
VVT Aim Angle #1*2
VVT aim angle (Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 80%
VVT duty signal value during intrusive operation.
VVT Change Angle #1*2
VVT change angle (Bank 1)/
Min.: 0° FR, Max.: 639.9° FR
0° FR: Idling
Displacement angle during intrusive operation.
VVT OCV Duty #1*2
VVT OCV operation duty (Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 100%
Requested duty value for intrusive operation.
VVT Aim Angle #2*2
VVT aim angle (Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 80%
VVT duty signal value during intrusive operation.
VVT Change Angle #2*2
VVT change angle (Bank 2)/
Min.: 0° FR, Max.: 639.9° FR
0° FR: Idling
Displacement angle during intrusive operation.
VVT OCV Duty #2*2
VVT OCV operation duty (Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 100%
Requested duty value for intrusive operation.
VVT Ex Hold Lrn Val #1*2
VVT exhaust hold duty ratio learning value (Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 80%
VVT duty signal value during intrusive operation.
VVT Ex Chg Angle #1*2
VVT exhaust change angle (Bank 1)/
Min.: 0° FR, Max.: 639.9° FR
0 to 5° FR: Idling
Displacement angle during intrusive operation.
VVT Ex OCV Duty #1*2
VVT exhaust OCV duty (Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 100%
Requested duty value for intrusive operation.
VVT Ex Hold Lrn Val #2*2
VVT exhaust hold duty ratio learning value (Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 80%
VVT duty signal value during intrusive operation.
VVT Ex Chg Angle #2*2
VVT exhaust change angle (Bank 2)/
Min.: 0° FR, Max.: 639.9° FR
0 to 5° FR: Idling
Displacement angle during intrusive operation.
VVT Ex OCV Duty #2*2
VVT exhaust OCV duty (Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 100%
Requested duty value for intrusive operation.
VN Turbo Type
Variable nozzle turbo type/
Not Avl or Commo or Vacuum or CAN Com
Not Avl (Unused)
-
Catalyst Temp B1S1
Catalyst temperature (Bank 1, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B2S1
Catalyst temperature (Bank 2, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B1S2
Catalyst temperature (Bank 1, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B2S2
Catalyst temperature (Bank 2, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
-
-
Starter Signal
Starter signal/
Open or Close
Open: Cranking
-
Power Steering Signal
Power steering switch signal/
ON or OFF
ON: Power steering operation
-
Neutral Position SW Signal*3
PNP switch status/
ON or OFF
ON: Shift lever in P or N
-
Clutch Switch*4
Clutch Switch/
ON or OFF
ON: Clutch pedal depressed
-
Stop Light Switch
Stop light switch/
ON or OFF
ON: Brake pedal depressed
-
A/C Signal
A/C switch status/
ON or OFF
ON: A/C ON
-
Closed Throttle Position SW
Closed throttle position switch/
ON or OFF
- ON: Throttle fully closed
- OFF: Throttle open
-
Fuel Cut Condition
Fuel cut condition/
ON or OFF
ON: Fuel cut operating
-
Immobiliser Communication
Immobiliser communication/
ON or OFF
ON: Normal
-
Check Mode
Check mode/
ON or OFF
ON: Check mode ON
Refer to the Check Mode Procedure
(Click here).
SPD Test Result
Check mode result for vehicle speed sensor/
Compl or Incmpl
-
-
Misfire Test Result
Check mode result for misfire monitor/
Compl or Incmpl
-
-
OXS1 Test Result
Check mode result for heated oxygen sensor (Bank 1)/
Compl or Incmpl
-
-
OXS2 Test Result
Check mode result for heated oxygen sensor (Bank 2)/
Compl or Incmpl
-
-
A/F Test Results #2
Check mode result for air fuel ratio sensor (Bank 2)/
Compl or Incmpl
-
-
A/F Test Results #1
Check mode result for air fuel ratio sensor (Bank 1)/
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Compl or Incmpl
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Compl or Incmpl
-
-
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Not Avl or Avail
-
-
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Compl or Incmpl
-
-
A/C Monitor
A/C Monitor/
Not Avl or Avail
-
-
A/C Monitor
A/C Monitor/
Compl or Incmpl
-
-
2nd Air Monitor
2nd air monitor/
Not Avl or Avail
-
-
2nd Air Monitor
2nd air monitor/
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor/
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor/
Compl or Incmpl
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Not Avl or Avail
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor/
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor/
Compl or Incmpl
-
-
Component Monitor ENA
Comprehensive component monitor/
Unable or Enable
-
-
Component Monitor CMPL
Comprehensive component monitor/
Compl or Incmpl
-
-
Fuel System Monitor ENA
Fuel system monitor/
Unable or Enable
-
-
Fuel System Monitor CMPL
Fuel system monitor/
Compl or Incmpl
-
-
Misfire Monitor ENA
Misfire monitor/
Unable or Enable
-
-
Misfire Monitor CMPL
Misfire monitor/
Compl or Incmpl
-
-
EGR/VVT Monitor ENA
EGR monitor/
Unable or Enable
-
-
EGR/VVT Monitor CMPL
EGR monitor/
Compl or Incmpl
-
-
Heater Monitor ENA
O2S (A/FS) heater monitor/
Unable or Enable
-
-
Heater Monitor CMPL
O2S (A/FS) heater monitor/
Compl or Incmpl
-
-
O2S(A/FS) Monitor ENA
O2S (A/FS) monitor/
Unable or Enable
-
-
O2S(A/FS) Monitor CMPL
O2S (A/FS) monitor/
Compl or Incmpl
-
-
A/C Monitor ENA
A/C monitor/
Unable or Enable
-
-
A/C Monitor CMPL
A/C monitor/
Compl or Incmpl
-
-
2nd Air Monitor ENA
2nd air monitor/
Unable or Enable
-
-
2nd Air Monitor CMPL
2nd air monitor/
Compl or Incmpl
-
-
EVAP Monitor ENA
EVAP monitor/
Unable or Enable
-
-
EVAP Monitor CMPL
EVAP monitor/
Compl or Incmpl
-
-
Heated Cat Monitor ENA
Heated catalyst monitor/
Unable or Enable
-
-
Heated Cat Monitor CMPL
Heated catalyst monitor/
Compl or Incmpl
-
-
Catalyst Monitor ENA
Catalyst monitor/
Unable or Enable
-
-
Catalyst Monitor CMPL
Catalyst monitor/
Compl or Incmpl
-
-
TC Terminal
TC terminal status/
ON or OFF
-
-
# Codes (Include History)
Number of codes/
Min.: 0, Max.: 255
-
Number of stored DTCs.
MIL
MIL status/
ON or OFF
ON: MIL on
-
MIL ON Run Distance
MIL on run distance/
Min.: 0 km, Max.: 65535 km
Distance after DTC stored
-
Running Time from MIL ON
Running time from MIL on/
Min.: 0 min, Max.: 65535 min
Equivalent to running time after MIL on
-
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 min, Max.: 65535 min
Equivalent to time after DTCs cleared
-
Distance from DTC Cleared
Distance after DTC cleared/
Min.: 0 km, Max.: 65535 km
Equivalent to drive distance after DTCs cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared/
Min.: 0, Max.: 255
-
Number of warm-up cycles after the DTC is cleared.
Dist Batt Cable Disconnect
Distance from battery cable disconnected/
Min.: 0 km, Max.: 65535 km
-
-
OBD Requirements
OBD requirement
OBD2 or E-OBD
-
Number of Emission DTC
Emission related DTCs/
Min.: 0 , Max.: 127
-
Number of emission related DTCs.
TC and TE1
TC and TE1 terminal of DLC3/
ON or OFF
-
-
Ignition Trig. Count
Ignition counter/
Min.: 0, Max.: 65535
0 to 600
-
Cylinder #1 Misfire Count
to
Cylinder #6 Misfire Count
Misfire count of the cylinder 1 to 6/
Min.: 0, Max.: 255
0
-
All Cylinders Misfire Count
All cylinders misfire count/
Min.: 0, Max.: 255
0
-
Misfire RPM
Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0
-
Misfire Load
Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0
-
Misfire Margin
Misfire monitoring/
Min.: -128%, Max.: 127%
-100 to 99.2%
Misfire detection margin
Engine Speed (Starter Off)
Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
-
For use when engine stall, starting problems or rough idle is present.
Starter Count
Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
-
For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip
Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km
-
For use when engine stall, starting problems or rough idle is present.
Engine Starting Time
Time elapsed after engine started (interval between ignition switch ON and off)/
Min.: 0 ms, Max.: 655350 ms
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp
Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp
Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature
Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C
Ambient temperature
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp
Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation
History of hesitation during engine start/
ON or OFF
-
-
Low Rev for Eng Start
History of low engine speed after engine start/
-
ON or OFF
-
-
Minimum Engine Speed
Minimum engine speed/
Min.: 0 rpm, Max.: 51199 rpm
-
For use when engine stall, starting problems or rough idle is present.
A/F Learn Value Idle #1
Air fuel ratio learn value area of idle (for Bank 1)/
Min.: -50%, Max.: 49.6%
-
-
A/F Learn Value Low #1
Air fuel ratio learn value area of low load (for Bank 1)/
Min.: -50%, Max.: 49.6%
-
-
A/F Learn Value Mid1 #1
Air fuel ratio learn value area of middle load 1 (for Bank 1)/
Min.: -50%, Max.: 49.6%
-
-
A/F Learn Value Mid2 #1
Air fuel ratio learn value area of middle load 2 (for Bank 1)/
Min.: -50%, Max.: 49.6%
-
-
A/F Learn Value High #1
Air fuel ratio learn value area of high load (for Bank 1)/
Min.: -50%, Max.: 49.6%
-
-
A/F Learn Value Idle #2
Air fuel ratio learn value area of idle (for Bank 2)/
Min.: -50%, Max.: 49.6%
-
-
A/F Learn Value Low #2
Air fuel ratio learn value area of low load (for Bank 2)/
Min.: -50%, Max.: 49.6%
-
-
A/F Learn Value Mid1 #2
Air fuel ratio learn value area of middle load 1 (for Bank 2)/
Min.: -50%, Max.: 49.6%
-
-
A/F Learn Value Mid2 #2
Air fuel ratio learn value area of middle load 2 (for Bank 2)/
Min.: -50%, Max.: 49.6%
-
-
A/F Learn Value High #2
Air fuel ratio learn value area of high load (for Bank 2)/
Min.: -50%, Max.: 49.6%
-
-
Power Steering Pressure
Power steering oil pressure/
Min.: 0 MPa, Max.: 25.599 MPa
-
-
ACT VSV
A/C cut status for Active Test/
ON or OFF
-
Active Test support data.
Idle Fuel Cut
Fuel cut idle/
ON or OFF
ON: Fuel cut operation
Idle Fuel Cut is "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
FC TAU
Fuel cut TAU: Fuel cut during very light load/
ON or OFF
ON: Fuel cut operation
The fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut
Status of the immobiliser fuel cut/
ON or OFF
-
-
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut History/
ON or OFF
-
-
Electrical Load Signal 1
Electrical load signal/
ON or OFF
-
-
Electrical Load Signal 2
Electrical load signal/
ON or OFF
-
-
Model Code
Model code
-
Identifying the model code:
GSJ1#.
Engine Type
Engine type
-
Identifying the engine type:
1GRFE.
Cylinder Number
Number of cylinders/
Min.: 0, Max.: 255
-
Identifying the number of cylinders:
6.
Transmission Type
Transmission type
-
Identifying the transmission type:
ECT 5th or MT.
Destination
Destination
-
Identifying the destination:
A or W
Model Year
Model year/
Min.: 1900, Max.: 2155
-
Identifying the model year:
20##
System Identification
System identification
-
Identifying the engine system:
Gasoline (gasoline engine).
Engine Speed of Cyl #1
Engine speed for cylinder 1/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #2
Engine speed for cylinder 2/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #3
Engine speed for cylinder 3/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #4
Engine speed for cylinder 4/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #5
Engine speed for cylinder 5/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test.
Engine Speed of Cyl #6
Engine speed for cylinder 6/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test.
Av Engine Speed of All Cyl
Engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test.
SPD (NT)*3
Input shaft speed/
Min.: 0 rpm, Max.: 12750 rpm
Lock-up is - ON (after warming up engine): Input turbine speed (NT) equal to engine speed
- OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
Data is displayed in increments of 50 rpm.
SPD (SP2)*3
Output shaft speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
-
- Normal Condition: If no conditions are specifically stated for "idling", the shift lever is in N or P, the A/C switch is off and all accessory switches are off.
- *1: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).
- *2: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2), Control the VVT Exhaust Linear (Bank 1) and Control the VVT Exhaust Linear (Bank 2). For other Active Tests, the Data List value will be 0.
- *3: for Automatic Transmission Models
- *4: for Manual Transmission Models
- 10 to 40%: Idling
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Injection Volume
Change injection volume
Between -12.5% and 24.8%
- All the injectors are tested at the same time.
- Perform the test at 3000 rpm or less.
- The injection volume can be changed in fine graduations within the control range.
Control the Injection Volume for A/F Sensor
Change injection volume
Lower by 12.5% or increase 25%
- Perform the test at 3000 rpm or less.
- Control the Injection Volume for A/F Sensor enables the checking and graphing of the A/F (Air Fuel Ratio) sensor voltage outputs.
- To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
Activate the VSV for Evap Control
Activate purge VSV control
ON/OFF
-
Control the A/C Cut Signal
Control A/C cut signal
ON/OFF
This test is possible when the following conditions are met: - Ignition switch ON.
- Engine stopped.
Control the Fuel Pump / Speed
Activate fuel pump
ON/OFF
This test is possible when the following conditions are met: - Ignition switch ON.
- Engine stopped.
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON/OFF
- ON: TC and TE1 connected.
- OFF: TC and TE1 disconnected.
Control the Idle Fuel Cut Prohibit
Prohibit idling fuel cut control
ON/OFF
-
Control the ETCS Open/Close Slow Speed
Throttle actuator
Close/Open
Open: throttle valve opens slowly
This test is possible when the following conditions are met: - Ignition switch ON.
- Engine stopped.
- Fully depressing the accelerator pedal (APP: 58 degrees or more).
Control the ETCS Open/Close Fast Speed
Throttle actuator
Close/Open
Open: throttle valve opens fast
This test is possible when the following conditions are met: - Ignition switch ON.
- Engine stopped.
- Fully depressing the accelerator pedal (APP: 58 degrees or more).
Control the VVT Linear (Bank 1)
Control Variable Valve Timing (VVT) [Bank 1]
-128 to 127% This value added to present OCV control duty
100%: Maximum advance
-100%: Maximum retard
- Engine stalls or idles roughly when VVT actuator is operated by 100%.
- Test is possible during idle.
Control the VVT System (Bank 1)
Turn on and off Oil Control Valve (OCV)
ON/OFF
- Engine stalls or idles roughly when OCV is turned on.
- Engine runs or idles normally when OCV is OFF.
Control the VVT Linear (Bank 2)
Control Variable Valve Timing (VVT) [Bank 2]
-128 to 127% This value added to present OCV control duty
100%: Maximum advance
-100%: Maximum retard
- Engine stalls or idles roughly when VVT actuator is operated by 100%.
- Test is possible during idle.
Control the VVT System (Bank 2)
Turn on and off Oil Control Valve (OCV)
ON/OFF
- Engine stalls or idles roughly when OCV is turned on.
- Engine runs or idles normally when OCV is OFF.
Control the VVT Exhaust Linear (Bank 1)
Control VVT (Bank 1)
128 to 127% This value added to present OCV control duty
100%: Maximum advance
-100%: Maximum retard
- Engine stalls or idles roughly when VVT actuator is operated by 100%.
- Test is possible while engine is idling.
Control the VVT Exhaust Linear (Bank 2)
Control VVT (Bank 2)
128 to 127% This value added to present OCV control duty
100%: Maximum advance
-100%: Maximum retard
- Engine stalls or idles roughly when VVT actuator is operated by 100%.
- Test is possible while engine is idling.
Control the Cylinder #1 Fuel Cut
Cylinder #1 injector fuel cut
ON/OFF
Test is possible while vehicle is stopped and engine is idling.
Control the Cylinder #2 Fuel Cut
Cylinder #2 injector fuel cut
ON/OFF
Test is possible while vehicle is stopped and engine is idling.
Control the Cylinder #3 Fuel Cut
Cylinder #3 injector fuel cut
ON/OFF
Test is possible while vehicle is stopped and engine is idling.
Control the Cylinder #4 Fuel Cut
Cylinder #4 injector fuel cut
ON/OFF
Test is possible while vehicle is stopped and engine is idling.
Control the Cylinder #5 Fuel Cut
Cylinder #5 injector fuel cut
ON/OFF
Test is possible while vehicle is stopped and engine is idling.
Control the Cylinder #6 Fuel Cut
Cylinder #6 injector fuel cut
ON/OFF
Test is possible while vehicle is stopped and engine is idling.
Control the All Cylinders Fuel Cut
All cylinder fuel cut
ON/OFF
Test is possible while vehicle is stopped and engine is idling.
Check the Cylinder Compression*
Check the cylinder compression pressure
ON/OFF
Fuel injection and ignition stop in all cylinders.
- HINT:
- *: When performing the Active Test item "Check the Cylinder Compression" and then cranking the engine, the ECM stops the fuel injection and ignition, and measures the engine speed for each cylinder.
- If one cylinder speed is higher than the others, that cylinder's compression pressure can be concluded to be lower than the others.
- Warm up the engine.
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester on.
- Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.
- Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl.
- Push the snapshot button to turn the snapshot function on.
- HINT:
- Using the snapshot function, data can be recorded during the Active Test.
- Press the RIGHT or LEFT button to change "Check the Cylinder Compression" to ON.
- HINT:
- Fuel injection and ignition for all cylinders are prohibited at this time, and each cylinder's engine speed measurement will enter standby mode.
- Crank the engine until the monitor item values "Engine speed of Cyl #1 to #6" and "Av Engine Speed of All Cyl" change.
- Monitor the engine speed (Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl) displayed on the tester.
- HINT:
- The tester displays extremely high values before cranking the engine. Each cylinder's engine speed is measured while cranking the engine and then the tester displays the actual engine speed values.
- NOTICE:
- The Active Test item "Check the Cylinder Compression" will automatically turn off 255 seconds after the Active Test is started.
- If the "Check the Cylinder Compression" test needs to be performed again after each cylinder's engine speed measurement has been performed once, press EXIT to return to the Active Test menu screen. Then perform the "Check the Cylinder Compression" test again.
- Use a fully-charged battery.
- The Active Test item "Check the Cylinder Compression" will automatically turn off 255 seconds after the Active Test is started.
- Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops
- CAUTION:
- If the Active Test is changed to OFF while the engine is being cranked, the engine will start.
- Push the snapshot button to turn the snapshot function off.
- Select the recorded data and display the data as a graph.
- Check the change in engine speed values.
- HINT:
- As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.
- All the injectors are tested at the same time.