2011-2016 FJ Cruiser · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built Aug 2011 – Jul 2012

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the tester, read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    The speed is indicated on speedometer.
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383 rpm
    650 to 750 rpm: Idling
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 10 to 40%: Idling
    2. 10 to 40%: Running without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load/
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from Mass Air Flow (MAF) meter/
    Min.: 0 gm/sec, Max.: 655.35 gm/sec
    2.5 to 4.7 gm/sec: Idling
    8.0 to 18.9 gm/sec: 2500 rpm
    If the mass air flow volume is approximately 0.0 gm/sec:
    1. The mass air flow meter power source circuit is open or short.
    2. The VG circuit is open or short.
    If the mass air flow volume is 271.0 gm/sec or more:
    1. The E2G circuit is open.
    Atmosphere Pressure
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure
    (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C, Max.: 140°C
    80 to 100°C (176 to 212°F): After warming up
    If the value is -40°C (-40°F): the sensor circuit is open.
    If the value is 140°C (284°F): the sensor circuit is shorted.
    Intake Air
    Intake air temperature/
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    If the value is -40°C (-40°F): the sensor circuit is open.
    If the value is 140°C (284°F): the sensor circuit is shorted.
    Engine Run Time
    Engine run time/
    Min.: 0 s, Max.: 65535 s
    Time after engine start
    Service data.
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 119.3°C
    Coolant temperature when engine started
    Service data.
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 119.3°C
    Intake air temperature when engine started
    Service data.
    Battery Voltage
    Battery voltage/
    Min.: 0 V, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Accelerator Position
    Accelerator pedal position/
    Min.: 0%, Max.: 399.9%
    Actual accelerator pedal position
    -
    Accel Sens. No.1 Volt %
    Absolute Accelerator Pedal Position (APP) No. 1/
    Min.: 0%, Max.: 100%
    10 to 22%: accelerator pedal released
    54 to 86%: accelerator pedal fully depressed
    -
    Accel Sens. No.2 Volt %
    Absolute APP No. 2/
    Min.: 0%, Max.: 100%
    12 to 42%: accelerator pedal released
    66 to 98%: accelerator pedal fully depressed
    -
    Accel Sensor Out No.1
    APP sensor No. 1 voltage/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: accelerator pedal released
    2.6 to 4.5 V: accelerator pedal fully depressed
    -
    Accel Sensor Out No.2
    APP sensor No. 2 voltage/
    Min.: 0 V, Max.: 4.98 V
    1.2 to 2.0 V: accelerator pedal released
    3.4 to 5.0 V: accelerator pedal fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No. 1/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data.
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No. 2/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data.
    Throttle Sensor Volt %
    Throttle valve opening percentage according to throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Accelerator pedal released
    2. 64 to 96%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA1.
    Throttl Sensor #2 Volt %
    Throttle valve opening percentage according to throttle position sensor No. 2/
    Min.: 0%, Max.: 100%
    1. 42 to 62%: Accelerator pedal released
    2. 92 to 100%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA2.
    ST1
    Brake pedal signal/
    ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard/
    ON or OFF
    -
    ETCS service data.
    Open Side Malfunction
    Open side malfunction/
    ON or OFF
    -
    ETCS service data.
    Throttle Idle Position
    Whether or not throttle position sensor detecting idling
    ON or OFF
    1. ON: Accelerator pedal released
    2. OFF: Accelerator pedal fully depressed
    -
    Throttle Require Position
    Required throttle position/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: Idling
    -
    Throttle Sensor Position*1
    Throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 0%: Accelerator pedal released
    2. 50 to 80%: Accelerator pedal fully depressed
    Recognition value for throttle opening angle on ECM.
    Throttle Position No. 1
    Throttle position sensor No. 1 output voltage/
    Min.: 0 V, Max.: 4.98 V
    1. 0.5 to 1.1 V: Accelerator pedal released
    2. 3.2 to 4.8 V: Accelerator pedal fully depressed
    3. 0.6 to 1.4 V: Fail-safe operating
    -
    Throttle Position No. 2
    Throttle position sensor No. 2 output voltage/
    Min.: 0 V, Max.: 4.98 V
    1. 2.1 to 3.1 V: Accelerator pedal released
    2. 4.6 to 5.0 V: Accelerator pedal fully depressed
    3. 2.1 to 3.1 V: Fail-safe operating
    -
    Throttle Position Command
    Throttle position command value/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 4.8 V
    -
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1/
    Min.: 0 V, Max.: 4.98 V
    0.6 to 1.4 V
    ETCS service data.
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2/
    Min.: 0 V, Max.: 4.98 V
    1.7 to 2.5 V
    ETCS service data.
    Throttle Motor Current
    Throttle motor current/
    Min.: 0 A, Max.: 19.9 A
    0 to 3.0 A: Idling
    ETCS service data.
    Throttle Motor DUTY
    Throttle actuator/
    Min.: 0%, Max.: 100%
    10 to 22%: Idling after engine warmed up
    ETCS service data.
    Throttle Motor Duty (Open)
    Throttle actuator duty ratio (open)/
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data.
    Throttle Motor Duty (Close)
    Throttle actuator duty ratio (closed)/
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data.
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value)/
    Min.: 0 V, Max.: 4.98 V
    0.4 to 1.0 V: Accelerator pedal released
    -
    +BM Voltage
    +BM voltage/
    Min.: 0 V, Max.: 79.998 V
    11 to 14 V: Ignition switch ON and system normal
    ETCS service data.
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    ON: Idling
    ETCS service data.
    Throttle Position
    Throttle valve opening angle/
    Min.: 0 deg, Max.: 499.99 deg
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    ISC Flow
    Flow rate calculated using information from each sensor/
    Min.: 0 L/s, Max.: 79.99 L/s
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    ISC Position
    Requested opening amount calculated using ISC control/
    Min.: 0 deg, Max.: 499.99 deg
    -
    This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).
    ISC Feedback Value
    ISC feedback compensation amount/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    ISC Learning Value
    ISC learned compensation amount/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Electric Load Feedback Val
    Compensation flow rate according to electrical load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Air Conditioner FB Val
    Compensation flow rate according to air conditioner load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    PS Feedback Val
    Power steering load feedback value: Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Low Revolution Control
    Low engine speed control operation state/
    ON or OFF
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Neutral Control
    Status of low engine speed control/
    ON or OFF
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    N Range Status*3
    Shift lever N status/
    ON or OFF
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Eng Stall Control FB Flow
    Intake air compensation flow rate/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Deposit Loss Flow
    Flow loss due to deposits/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    1. This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.
    2. Check this value for reference when the engine stalls, is difficult to start, or idles roughly.
    3. When the ISC learned value is initialized by disconnecting the battery negative terminal or removing the fuses (EFI and ETCS fuses), performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.
      1. Start the engine cold and allow the engine to idle.
      2. After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.
      3. Turn the ignition switch off and wait for 30 seconds.
      4. Start the engine again, and allow the engine to idle for 5 minutes.
    Injector (Port)
    Injection period of the No. 1 cylinder/
    Min.: 0 μs, Max.: 65535 μs
    1600 to 2700 μs: idling
    -
    Injection Volum (Cylinder 1)
    Injection volume (cylinder 1)/
    Min.: 0 ml, Max.: 2.047 ml
    0 to 0.5 ml
    Quantity of fuel injection volume for 10 times.
    Fuel Pump/Speed Status
    Fuel pump/speed status/
    ON or OFF
    -
    Active Test support data.
    Current Fuel Type
    Current fuel type
    -
    Identifying the current fuel type:
    Gasoline
    EVAP (Purge) VSV
    Purge VSV control duty/
    Min.: 0%, Max.: 100%
    0 to 100%: During idling
    Order signal from ECM.
    Evap Purge Flow
    Purge flow/
    Min.: 0%, Max.: 399.9%
    0 to 100%: Idling
    -
    Purge Density Learn Value
    Learning value of purge density/
    Min.: -200, Max.: 199.993
    -40 to 0%: Idling
    Service data.
    Vapor pressure (calculated)
    Calculated EVAP system pressure/
    Min.: -720.896 kPa, Max.: 720.874 kPa
    Approximately 100 kPa: Ignition switch ON
    -
    EVAP Purge VSV
    VSV status for EVAP control/
    ON or OFF
    -
    Active Test support data.
    Purge Cut VSV Duty
    Purge cut VSV duty/
    Min.: 0%, Max.: 399.9%
    -
    -
    Target Air-Fuel Ratio
    Air fuel ratio:
    Min.: 0, Max.: 1.99
    0.8 to 1.2: During idling
    -
    AF Lambda B1S1
    Short-term fuel trim associated with the Bank 1 Sensor 1/
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio = 1
    3. Value more than 1 (1.001 to 1.999) = Lean
    -
    AF Lambda B2S1
    Short-term fuel trim associated with the Bank 2 Sensor 1/
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio = 1
    3. Value more than 1 (1.001 to 1.999) = Lean
    -
    AFS Voltage B1S1
    Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS Voltage B2S1
    Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS Current B1S1
    Air fuel ratio sensor current Bank 1 Sensor 1/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
    AFS Current B2S1
    Air fuel ratio sensor current (for Bank 2 Sensor 1)/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
    A/F Heater Duty #1
    A/F heater duty ratio (for Bank 1)
    Min.: 0%, Max.: 399.9%
    0 to 100 %
    -
    A/F Heater Duty #2
    A/F heater duty ratio (for Bank 2)
    Min.: 0%, Max.: 399.9%
    0 to 100 %
    -
    O2S B1S2
    Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    O2S B2S2
    Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    O2S Impedance B1S2
    Heated oxygen sensor impedance (Bank 1 Sensor 2)/
    Min.: 0 ohm, Max.: 21247.67 ohm
    5 to 15000 ohm
    -
    O2S Impedance B2S2
    Heated oxygen sensor impedance (Bank 2 Sensor 2)/
    Min.: 0 ohm, Max.: 21247.67 ohm
    5 to 15000 ohm
    -
    O2 Heater B1S2
    Heated oxygen sensor heater for bank 1 sensor 2/
    Not Act or Active
    -
    -
    O2 Heater B2S2
    Heated oxygen sensor heater for bank 2 sensor 2/
    Not Act or Active
    -
    -
    O2 Heater Curr Val B1S2
    Heated oxygen sensor current for bank 1 sensor 2/
    Min.: 0 A, Max.: 4.999 A
    -
    -
    O2 Heater Curr Val B2S2
    Heated oxygen sensor current for bank 2 sensor 2/
    Min.: 0 A, Max.: 4.999 A
    -
    -
    Short FT #1
    Short-term fuel trim of Bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
    Long FT #1
    Long-term fuel trim of Bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    This item refers to the overall fuel compensation carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
    Total FT #1
    Total fuel trim of Bank 1
    Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    -
    Short FT #2
    Short-term fuel trim of Bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
    Long FT #2
    Long-term fuel trim of Bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    This item refers to the overall fuel compensation carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
    Total FT #2
    Total fuel trim of Bank 2
    Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    -
    Fuel System Status #1
    Fuel system status (Bank 1)/
    OL, CL, OLDrive, OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
    2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
    3. OLDrive: Open loop due to driving conditions (fuel enrichment).
    4. OLFault: Open loop due to a detected system fault.
    5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
    Fuel System Status #2
    Fuel system status (Bank 2)/
    OL, CL, OLDrive, OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
    2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
    3. OLDrive: Open loop due to driving conditions (fuel enrichment).
    4. OLFault: Open loop due to a detected system fault.
    5. CLFault: Closed loop but the air fuel ration sensor, which is used for fuel control, is malfunctioning.
    IGN Advance
    Ignition timing advance for No. 1 cylinder/
    Min.: -64 deg, Max.: 63.5 deg
    BTDC 7 to 24°: Idling
    -
    Knock Feedback Value
    Feedback value of knocking/
    Min.: -1024°CA, Max.: 1023.9°CA
    -22 to 0° CA:
    Driving, 70 km/h (44 mph)
    Service data.
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min.: -1024°CA, Max.: 1023.9°CA
    0 to 22° CA:
    Driving, 70 km/h (44 mph)
    Service data.
    Idle Spark Advn Ctrl #1
    Individual cylinder timing advance compensation amount (No. 1)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Idle Spark Advn Ctrl #2
    Individual cylinder timing advance compensation amount (No. 2)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Idle Spark Advn Ctrl #3
    Individual cylinder timing advance compensation amount (No. 3)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Idle Spark Advn Ctrl #4
    Individual cylinder timing advance compensation amount (No. 4)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Idle Spark Advn Ctrl #5
    Individual cylinder timing advance compensation amount (No. 5)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Idle Spark Advn Ctrl #6
    Individual cylinder timing advance compensation amount (No. 6)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    VVT Control Status #1
    Variable valve timing (VVT) control status (Bank 1)/
    ON or OFF
    -
    Active Test support data.
    VVT Control Status #2
    VVT control status (Bank 2)/
    ON or OFF
    -
    Active Test support data.
    VVT Advance Fail
    VVT control failure status/
    ON or OFF
    ON: VVT control failure
    -
    VVT Aim Angle #1*2
    VVT aim angle (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Change Angle #1*2
    VVT change angle (Bank 1)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT OCV Duty #1*2
    VVT OCV operation duty (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    VVT Aim Angle #2*2
    VVT aim angle (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Change Angle #2*2
    VVT change angle (Bank 2)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT OCV Duty #2*2
    VVT OCV operation duty (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    VVT Ex Hold Lrn Val #1*2
    VVT exhaust hold duty ratio learning value (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Ex Chg Angle #1*2
    VVT exhaust change angle (Bank 1)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT Ex OCV Duty #1*2
    VVT exhaust OCV duty (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    VVT Ex Hold Lrn Val #2*2
    VVT exhaust hold duty ratio learning value (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Ex Chg Angle #2*2
    VVT exhaust change angle (Bank 2)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT Ex OCV Duty #2*2
    VVT exhaust OCV duty (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    VN Turbo Type
    Variable nozzle turbo type/
    Not Avl or Commo or Vacuum or CAN Com
    Not Avl (Unused)
    -
    Catalyst Temp B1S1
    Catalyst temperature (Bank 1, Sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2S1
    Catalyst temperature (Bank 2, Sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B1S2
    Catalyst temperature (Bank 1, Sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2S2
    Catalyst temperature (Bank 2, Sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Starter Signal
    Starter signal/
    ON or OFF
    Open: Cranking
    -
    Power Steering Signal
    Power steering switch signal/
    ON or OFF
    ON: Power steering operation
    -
    Neutral Position SW Signal*3
    PNP switch status/
    ON or OFF
    ON: Shift lever in P or N
    -
    Clutch Switch*4
    Clutch Switch/
    ON or OFF
    ON: Clutch pedal depressed
    -
    4WD SW
    4WD switch
    ON or OFF
    ON: 4WD ON
    -
    Stop Light Switch
    Stop light switch/
    ON or OFF
    ON: Brake pedal depressed
    -
    A/C Signal
    A/C switch status/
    ON or OFF
    ON: A/C ON
    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Fuel Cut Condition
    Fuel cut condition/
    ON or OFF
    ON: Fuel cut operating
    -
    Immobiliser Communication
    Immobiliser communication/
    ON or OFF
    ON: Normal
    -
    Check Mode
    Check mode/
    ON or OFF
    ON: Check mode ON
    Refer to the Check Mode Procedure
    (Click here).
    SPD Test Result
    Check mode result for vehicle speed sensor/
    Compl or Incmpl
    -
    -
    Misfire Test Result
    Check mode result for misfire monitor/
    Compl or Incmpl
    -
    -
    OXS1 Test Result
    Check mode result for heated oxygen sensor (Bank 1)/
    Compl or Incmpl
    -
    -
    OXS2 Test Result
    Check mode result for heated oxygen sensor (Bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #2
    Check mode result for air fuel ratio sensor (Bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #1
    Check mode result for air fuel ratio sensor (Bank 1)/
    Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor/
    Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor
    A/C Monitor/
    Not Avl or Avail
    -
    -
    A/C Monitor
    A/C Monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor/
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Not Avl or Avail
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    Component Monitor ENA
    Comprehensive component monitor/
    Unable or Enable
    -
    -
    Component Monitor CMPL
    Comprehensive component monitor/
    Compl or Incmpl
    -
    -
    Fuel System Monitor ENA
    Fuel system monitor/
    Unable or Enable
    -
    -
    Fuel System Monitor CMPL
    Fuel system monitor/
    Compl or Incmpl
    -
    -
    Misfire Monitor ENA
    Misfire monitor/
    Unable or Enable
    -
    -
    Misfire Monitor CMPL
    Misfire monitor/
    Compl or Incmpl
    -
    -
    EGR/VVT Monitor ENA
    EGR monitor/
    Unable or Enable
    -
    -
    EGR/VVT Monitor CMPL
    EGR monitor/
    Compl or Incmpl
    -
    -
    Heater Monitor ENA
    O2S (A/FS) heater monitor/
    Unable or Enable
    -
    -
    Heater Monitor CMPL
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor ENA
    O2S (A/FS) monitor/
    Unable or Enable
    -
    -
    O2S(A/FS) Monitor CMPL
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor ENA
    A/C monitor/
    Unable or Enable
    -
    -
    A/C Monitor CMPL
    A/C monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor ENA
    2nd air monitor/
    Unable or Enable
    -
    -
    2nd Air Monitor CMPL
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor ENA
    EVAP monitor/
    Unable or Enable
    -
    -
    EVAP Monitor CMPL
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Cat Monitor ENA
    Heated catalyst monitor/
    Unable or Enable
    -
    -
    Heated Cat Monitor CMPL
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor ENA
    Catalyst monitor/
    Unable or Enable
    -
    -
    Catalyst Monitor CMPL
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    TC Terminal
    TC terminal status/
    ON or OFF
    -
    -
    # Codes (Include History)
    Number of codes/
    Min.: 0, Max.: 255
    -
    Number of stored DTCs.
    MIL
    MIL status/
    ON or OFF
    ON: MIL on
    -
    MIL ON Run Distance
    MIL on run distance/
    Min.: 0 Km, Max.: 65535 Km
    Distance after DTC stored
    (MIL turns on)
    -
    Running Time from MIL ON
    Running time from MIL on/
    Min.: 0 min, Max.: 65535 min
    Equivalent to running time after MIL on
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 min, Max.: 65535 min
    Equivalent to time after DTCs cleared
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km, Max.: 65535 km
    Equivalent to drive distance after DTCs cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after the DTC is cleared.
    Dist Batt Cable Disconnect
    Distance from battery cable disconnected/
    Min.: 0 Km, Max.: 65535 Km
    -
    -
    OBD Requirements
    OBD requirement
    OBD II (California ARB) or EOBD (Euro OBD)
    -
    Number of Emission DTC
    Emission related DTCs/
    Min.: 0 , Max.: 127
    -
    Number of emission related DTCs.
    TC and TE1
    TC and TE1 terminal of DLC3/
    ON or OFF
    -
    -
    Ignition Trig. Count
    Ignition counter/
    Min.: 0, Max.: 65535
    0 to 600
    -
    Cylinder #1 Misfire Count
    to
    Cylinder #6 Misfire Count
    Misfire count of the cylinder 1 to 6/
    Min.: 0, Max.: 255
    0
    -
    All Cylinders Misfire Count
    All cylinders misfire count/
    Min.: 0, Max.: 255
    0
    -
    Misfire RPM
    Engine speed for first misfire range/
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range/
    Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire monitoring/
    Min.: -128%, Max.: 127%
    0 to 99.2%
    Misfire detection margin
    Engine Speed (Starter Off)
    Engine speed when starter off/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Starter Count
    Number of times starter turned on after ignition switch turned to ON/
    Min.: 0, Max.: 255
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Run Dist of Previous Trip
    Distance driven during previous trip/
    Min.: 0 km, Max.: 655.35 km
    -
    Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
    After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
    HINT:
    Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when the DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.
    Engine Starting Time
    Time elapsed after engine started (interval between ignition switch ON and off)/
    Min.: 0 ms, Max.: 655350 ms
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Previous Trip Coolant Temp
    Engine coolant temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Previous Trip Intake Temp
    Intake air temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Engine Oil Temperature
    Engine oil temperature (estimated temperature)/
    Min.: -40°C, Max.: 215°C
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Previous Trip Eng Oil Temp
    Engine oil temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Ambient Temp for A/C
    Ambient temperature
    Min.: -40°C, Max.: 215°C
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Previous Trip Ambient Temp
    Ambient temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    Engine Start Hesitation
    History of hesitation during engine start/
    ON or OFF
    -
    -
    Low Rev for Eng Start
    History of low engine speed after engine start/
    -
    ON or OFF
    -
    -
    Minimum Engine Speed
    Minimum engine speed/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Reference:
    Check the value when engine stalls, is difficult to start, or idles roughly.
    A/F Learn Value Idle #1
    Air fuel ratio learn value area of idle (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Low #1
    Air fuel ratio learn value area of low load (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid1 #1
    Air fuel ratio learn value area of middle load 1 (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid2 #1
    Air fuel ratio learn value area of middle load 2 (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value High #1
    Air fuel ratio learn value area of high load (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Idle #2
    Air fuel ratio learn value area of idle (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Low #2
    Air fuel ratio learn value area of low load (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid1 #2
    Air fuel ratio learn value area of middle load 1 (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid2 #2
    Air fuel ratio learn value area of middle load 2 (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value High #2
    Air fuel ratio learn value area of high load (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -
    -
    Power Steering Pressure
    Power steering oil pressure/
    Min.: 0 MPa, Max.: 25.599 MPa
    -
    -
    ACT VSV
    A/C cut status for Active Test/
    ON or OFF
    -
    Active Test support data.
    Brake Override System
    Brake override system status/
    ON or OFF
    ON: Brake override system operating
    -
    Idle Fuel Cut
    Fuel cut idle/
    ON or OFF
    ON: Fuel cut operation
    Idle Fuel Cut is "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
    FC TAU
    Fuel cut TAU: Fuel cut during very light load/
    ON or OFF
    ON: Fuel cut operation
    The fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
    Immobiliser Fuel Cut
    Status of the immobiliser fuel cut/
    ON or OFF
    -
    -
    Immobiliser Fuel Cut History
    Status of the immobiliser fuel cut History/
    ON or OFF
    -
    -
    Electrical Load Signal 1
    Electrical load signal/
    ON or OFF
    -
    -
    Electrical Load Signal 2
    Electrical load signal/
    ON or OFF
    -
    -
    Model Code
    Model code
    -
    Identifying the model code:
    GSJ1#.
    Engine Type
    Engine type
    -
    Identifying the engine type:
    1GRFE.
    Cylinder Number
    Number of cylinders/
    Min.: 0, Max.: 255
    -
    Identifying the number of cylinders:
    6.
    Transmission Type
    Transmission type
    -
    Identifying the transmission type:
    ECT 5th or MT.
    Destination
    Destination
    -
    Identifying the destination:
    A or W
    Model Year
    Model year/
    Min.: 1900, Max.: 2155
    -
    Identifying the model year:
    20##
    System Identification
    System identification
    -
    Identifying the engine system:
    Gasoline (gasoline engine).
    Engine Speed of Cyl #1
    Engine speed for cylinder 1/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #2
    Engine speed for cylinder 2/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #3
    Engine speed for cylinder 3/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #4
    Engine speed for cylinder 4/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #5
    Engine speed for cylinder 5/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #6
    Engine speed for cylinder 6/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Av Engine Speed of All Cyl
    Engine speed for all cylinders/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    SPD (NT)*3
    Input shaft speed/
    Min.: 0 rpm, Max.: 12750 rpm
    Lock-up is
    1. ON (after warming up engine): Input turbine speed (NT) equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
    Data is displayed in increments of 50 rpm.
    SPD (SP2)*3
    Output shaft speed/
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
    -
    1. Normal Condition: If no conditions are specifically stated for "idling", the shift lever is in N or P, the A/C switch is off and all accessory switches are off.
    2. *1: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).
    3. *2: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2), Control the VVT Exhaust Linear (Bank 1) and Control the VVT Exhaust Linear (Bank 2). For other Active Tests, the Data List value will be 0.
    4. *3: for Automatic Transmission Models
    5. *4: for Manual Transmission Models


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the tester on.

  4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  5. According to the display on the tester, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5% and 24.8%
    1. All the injectors are tested at the same time.
    2. Perform the test at 3000 rpm or less.
    3. The injection volume can be changed in fine graduations within the control range.
    Control the Injection Volume for A/F Sensor
    Change injection volume
    -12.5%/0%/12.5%
    1. Perform the test at 3000 rpm or less.
    2. Control the Injection Volume for A/F Sensor enables the checking and graphing of the A/F (Air Fuel Ratio) sensor voltage outputs.
    3. To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    -
    Control the A/C Cut Signal
    Control A/C cut signal
    ON/OFF
    This test is possible when the following conditions are met:
    1. Ignition switch ON.
    2. Engine stopped.
    Control the Fuel Pump / Speed
    Activate fuel pump
    ON/OFF
    This test is possible when the following conditions are met:
    1. Ignition switch ON.
    2. Engine stopped.
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected.
    2. OFF: TC and TE1 disconnected.
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    Close/Open
    Open: throttle valve opens slowly
    This test is possible when the following conditions are met:
    1. Ignition switch ON.
    2. Engine stopped.
    3. Fully depressing the accelerator pedal (APP: 58 degrees or more).
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    Close/Open
    Open: throttle valve opens fast
    This test is possible when the following conditions are met:
    1. Ignition switch ON.
    2. Engine stopped.
    3. Fully depressing the accelerator pedal (APP: 58 degrees or more).
    Control the VVT Linear (Bank 1)
    Control VVT (for intake camshaft of bank 1)
    -128 to 127% This value added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
    2. Test is possible during idle.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT System (Bank 1)
    Turn on and off Oil Control Valve (bank 1)
    ON/OFF
    1. Engine stalls or idles roughly when OCV is turned on.
    2. Engine runs or idles normally when OCV is OFF.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Linear (Bank 2)
    Control VVT (for intake camshaft of bank 2)
    -128 to 127% This value added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
    2. Test is possible during idle.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT System (Bank 2)
    Turn on and off Oil Control Valve (bank 2)
    ON/OFF
    1. Engine stalls or idles roughly when OCV is turned on.
    2. Engine runs or idles normally when OCV is OFF.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Exhaust Linear (Bank 1)
    Control VVT (for exhaust camshaft of bank 1)
    -128 to 127% This value added to present OCV control duty
    100%: Maximum retard
    -100%: Maximum advance
    1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
    2. Test is possible while engine is idling.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Exhaust Linear (Bank 2)
    Control VVT (for exhaust camshaft of bank 2)
    -128 to 127% This value added to present OCV control duty
    100%: Maximum retard
    -100%: Maximum advance
    1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
    2. Test is possible while engine is idling.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the Cylinder #1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.
    Control the Cylinder #2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.
    Control the Cylinder #3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.
    Control the Cylinder #4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.
    Control the Cylinder #5 Fuel Cut
    Cylinder #5 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.
    Control the Cylinder #6 Fuel Cut
    Cylinder #6 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.
    Control the All Cylinders Fuel Cut
    All cylinder fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.
    Check the Cylinder Compression*
    Check the cylinder compression pressure
    ON/OFF
    Fuel injection and ignition stop in all cylinders.

    HINT:
    *: When performing the Active Test item "Check the Cylinder Compression" and then cranking the engine, the ECM stops the fuel injection and ignition, and measures the engine speed for each cylinder.
    If one cylinder speed is higher than the others, that cylinder's compression pressure can be concluded to be lower than the others.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the intelligent tester to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the tester on.
    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.
    7. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl.
    8. Push the snapshot button to turn the snapshot function on.

      HINT:
      Using the snapshot function, data can be recorded during the Active Test.

    9. Press the RIGHT or LEFT button to change "Check the Cylinder Compression" to ON.

      HINT:
      Fuel injection and ignition for all cylinders are prohibited at this time, and each cylinder's engine speed measurement will enter standby mode.

    10. Crank the engine until the monitor item values "Engine speed of Cyl #1 to #6" and "Av Engine Speed of All Cyl" change.
    11. Monitor the engine speed (Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl) displayed on the tester.

      HINT:
      The tester displays extremely high values before cranking the engine. Each cylinder's engine speed is measured while cranking the engine and then the tester displays the actual engine speed values.

      NOTICE:
      1. The Active Test item "Check the Cylinder Compression" will automatically turn off 255 seconds after the Active Test is started.
      2. If the "Check the Cylinder Compression" test needs to be performed again after each cylinder's engine speed measurement has been performed once, press EXIT to return to the Active Test menu screen. Then perform the "Check the Cylinder Compression" test again.
      3. Use a fully-charged battery.

    12. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops

      CAUTION:
      If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

    13. Push the snapshot button to turn the snapshot function off.
    14. Select the recorded data and display the data as a graph.
    15. Check the change in engine speed values.

      HINT:
      As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.

← DATA LIST / ACTIVE TEST (Nov 2010 – Jul 2011)DATA LIST / ACTIVE TEST (Aug 2012 – Jul 2014) →