2011-2016 FJ Cruiser · Service Manual ENGINE

P0010 Camshaft Position "A" Actuator Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

HINT:
This DTC relates to the Oil Control Valve (OCV).

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine running, the ECM will illuminate the MIL and set the DTC.
The VVT (variable valve timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies the 12 volts to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position etc.
A117755E02
DTC No.
DTC Detection Conditions
Trouble Areas
P0010
Open or short in OCV (bank 1) circuit
(1 trip detection logic)
  1. Open or short in OCV (bank 1) circuit
  2. OCV (bank 1)
  3. ECM
P0020
Open or short in OCV (bank 2) circuit
(1 trip detection logic)
  1. Open or short in OCV (bank 2) circuit
  2. OCV (bank 2)
  3. ECM

MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine running, the ECM will illuminate the MIL and set the DTC.

WIRING DIAGRAM

A133454E01

INSPECTION PROCEDURE


1. CHECK FOR DTC (DTC P0010 OR P0020)
  1. Clear the DTCs after recording the freeze frame data and DTCs.

  1. Allow the engine to idle and check for DTCs.

  1. Check whether P0010 or P0020 is present.

OK:
P0010 or P0020 is present.



NG
CHECK FOR INTERMITTENT PROBLEMS (Click here)
OK


2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
A095415E05
  1. Disconnect the OCV connector.

  1. Measure the resistance between the terminals of the OCV.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    1 - 2
    6.9 to 7.9 Ω at 20°C (68°F)

  1. Reconnect the OCV connector.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (OCV - ECM)
A133481E01
  1. Disconnect the B3 ECM connector.

  1. Disconnect the B12 or B26 OCV connector.

  1. Check the resistance.

    Standard Resistance for Bank 1:
    Tester Connections
    Specified Conditions
    B12-1 - OC1+ (B3-17)
    Below 1 Ω
    B12-1 - Body ground
    10 kΩ or higher
    B12-2 - OC1- (B3-16)
    Below 1 Ω
    B12-2 - Body ground
    10 kΩ or higher

    Standard Resistance for Bank 2:
    Tester Connections
    Specified Conditions
    B26-1 - OC2+ (B3-15)
    Below 1 Ω
    B26-1 - Body ground
    10 kΩ or higher
    B26-2 - OC2- (B3-14)
    Below 1 Ω
    B26-2 - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the OCV connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2014)P0010 Camshaft Position "A" Actuator Circuit (Bank 1) (+ P0020) (from Aug 2009) →