2011-2016 FJ Cruiser · Service Manual ENGINE

P0010 Camshaft Position "A" Actuator Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

  1. This DTC is designed to detect opens or shorts in the Camshaft Timing Oil Control Valve (OCV) assembly circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
  2. The VVT (Variable Valve Timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft timing gear assembly to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
A209140E07
DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in OCV (for intake side of bank 1) circuit
(1 trip detection logic)
  1. Open or short in OCV (for intake side of bank 1) circuit
  2. OCV (for intake side of bank 1)
  3. ECM
P0020
Open or short in OCV (for intake side of bank 2) circuit
(1 trip detection logic)
  1. Open or short in OCV (for intake side of bank 2) circuit
  2. OCV (for intake side of bank 2)
  3. ECM

HINT:
This DTC relates to the Oil Control Valve (OCV).


MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the Camshaft Timing Oil Control Valve (OCV) assembly circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and stores the DTC.

WIRING DIAGRAM

A178641E04

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK DTC (P0010 OR P0020)
  1. Connect the intelligent tester to the DLC3.

  1. Clear DTC after recording the freeze frame data and DTC (Click here).

  1. Turn the ignition switch off.

  1. Allow the engine to idle and check DTC.

  1. Check that P0010 or P0020 is not present.

    OK:
    P0010 or P0020 is not present.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A160397E17
    Disconnect the camshaft timing oil control valve assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Camshaft Timing Oil Control Valve Assembly)



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (OCV - ECM)
  1. Disconnect the OCV connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B61-1 - B48-19 (OC1+)
    Always
    Below 1 Ω
    B61-2 - B48-20 (OC1-)
    Always
    Below 1 Ω
    B62-1 - B47-19 (OC2+)
    Always
    Below 1 Ω
    B62-2 - B47-20 (OC2-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B61-1 or B48-19 (OC1+) - Body ground
    Always
    10 kΩ or higher
    B61-2 or B48-20 (OC1-) - Body ground
    Always
    10 kΩ or higher
    B62-1 or B47-19 (OC2+) - Body ground
    Always
    10 kΩ or higher
    B62-2 or B47-20 (OC2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0010 Camshaft Position "A" Actuator Circuit (Bank 1) (+ P0020) (Jul 2007 – Jul 2009)P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012, P0021, P0022) (Jul 2007 – Nov 2007) →