P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance
Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
DESCRIPTION
- HINT:
- Refer to DTC P2120 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2121
Difference between VPA and VPA2 less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic)
- Accelerator Pedal Position (APP) sensor
- ECM
- Accelerator Pedal Position (APP) sensor
MONITOR DESCRIPTION
When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the Accelerator Pedal Position (APP) sensor is malfunctioning. The ECM turns on the MIL and the DTC is stored.FAIL-SAFE
The Accelerator Pedal Position (APP) sensor has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to Fail-safe mode. In Fail-safe mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to a normal condition.
WIRING DIAGRAM
Refer to DTC P2120 (Click here).INSPECTION PROCEDURE
- HINT:
- This DTC relates to the Accelerator Pedal Position (APP) sensor.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- This DTC relates to the Accelerator Pedal Position (APP) sensor.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
Result Result
Proceed to
P2121 is output
A
P2121 and other DTCs are output
B
- HINT:
- If any DTCs other than P2121 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the values displayed on the intelligent tester.
- Standard Voltage:
Accelerator Pedal Operation
Accel Sensor Out No. 1
Accel Sensor Out No. 2
Released
0.5 to 1.1 V
1.2 to 2.0 V
Depressed
2.6 to 4.5 V
3.4 to 5.0 V
|
|
||||
| OK | ||
| ||
| 3. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2121) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
Result Result
Proceed to
P2121 is output
A
No DTC is output
B
|
|
||||
| A | ||
| ||


