2011-2016 FJ Cruiser · Service Manual ENGINE

P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

HINT:
This DTC relates to the Accelerator Pedal Position (APP) sensor.

Refer to DTC P2120 (Click here).
DTC No.
DTC Detection Conditions
Trouble Areas
P2121
Difference between VPA and VPA2 less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic)
  1. Accelerator pedal position sensor (Accelerator pedal rod assembly)
  2. ECM

MONITOR DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2. VPA is used to detect the actual accelerator pedal angle (used for engine control) and VPA2 is used to detect malfunctions in VPA. When the difference between the voltage outputs of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is a malfunctioning. The ECM turns on the MIL and the DTC is set.

FAIL-SAFE

The accelerator pedal position sensor has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.
If a pass condition is detected and then the ignition switch is turned OFF, the fail-safe operation stops and the system returns to a normal condition.

WIRING DIAGRAM

Refer to DTC P2120 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION NO. 1 AND ACCELERATOR POSITION NO. 2)
FI07052E06
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

  1. Read the values displayed on the tester.

    Standard Voltage:
    Accelerator Pedal
    Operations
    Accelerator Position No. 1
    Accelerator Position No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 5.0 V



OK
Go to step 3
NG


2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
A116156E02
  1. Disconnect the A2 Accelerator Pedal Position (APP) sensor connector.

  1. Disconnect the E47 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    VPA (A2-6) - VPA (E47-18)
    Below 1 Ω
    EPA (A2-5) - EPA (E47-20)
    VCPA (A2-4) - VCPA (E47-26)
    VPA2 (A2-3) - VPA2 (E47-19)
    EPA2 (A2-2) - EPA2 (E47-21)
    VCP2 (A2-1) - VCP2 (E47-27)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    VPA (A2-6) or VPA (E47-18) - Body ground
    10 kΩ or higher
    EPA (A2-5) or EPA (E47-20) - Body ground
    VCPA (A2-4) or VCPA (E47-26) - Body ground
    VPA2 (A2-3) or VPA2 (E47-19) - Body ground
    EPA2 (A2-2) or EPA2 (E47-21) - Body ground
    VCP2 (A2-1) or VCP2 (E47-27) - Body ground

  1. Reconnect the APP sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
Replace the accelerator pedal rod assembly (Click here).

NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Fully depress and release the accelerator pedal several times quickly.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P2121
    A
    No output
    B



B
END
A

REPLACE ECM (Click here)


← P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (from Nov 2010)P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (Aug 2009 – Oct 2010) →