2011-2016 FJ Cruiser · Service Manual ENGINE

P0505 Idle Control System Malfunction

Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014

DESCRIPTION

The idling speed is controlled by the ETCS (Electronic Throttle Control System). The ETCS is comprised of: 1) the one valve type throttle body; 2) the throttle actuator, which operates the throttle valve; 3) the Throttle Position (TP) sensor, which detects the opening angle of the throttle valve; 4) the Accelerator Pedal Position (APP) sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the ETCS. Based on the target idling speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.
DTC No.
DTC Detection Condition
Trouble Area
P0505
Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
  1. ETCS
  2. Air induction system
  3. PCV valve and hose
  4. PCV hose connection
  5. ECM

MONITOR DESCRIPTION

The ECM monitors the idling speed and idling air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if the following conditions are met:
  1. The learned idling air flow volume remains at the maximum or minimum volume for 5 seconds during a drive cycle.
  2. After driving at a vehicle speed of 10 km/h ( 6.25 mph) or more, the actual engine idling speed minus the target idling speed is less than -100 rpm or 150 rpm or more when the A/C is off and shift position is not neutral, or less than -100 rpm or 200 rpm or more when the A/C is on or shift position is neutral, 5 times or more during a driving cycle.
A121611E01

INSPECTION PROCEDURE

HINT:
  1. The following conditions may also cause DTC P0505 to be set:
    1. (1) The floor carpet overlapping slightly onto the accelerator pedal, causing the accelerator pedal to be slightly depressed and therefore the throttle valve position to be slightly open.
    2. (2) The accelerator pedal being not fully released.
  2. Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0505 is output
    A
    P0505 and other DTCs is output
    B

    HINT:
    If any DTCs other than P0505 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leak.

    OK:
    No leak from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


4. INSPECT THROTTLE VALVE
  1. Check the throttle valve condition (Click here).



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)


← P0505 Idle Control System Malfunction (Dec 2007 – Jul 2009)P0505 Idle Control System Malfunction (Nov 2010 – Jul 2014) →