2011-2016 FJ Cruiser · Service Manual RESTRAINTS

DISPOSAL

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures described d below are for the LH side.
  3. When scrapping a vehicle equipped with the SRS or disposing of the curtain shield airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with airbag deployment, contact the SERVICE DEPT. of TOYOTA MOTOR SALES, U.S.A., INC.

CAUTION:
  1. Never dispose of a curtain shield airbag assembly that has an undeployed airbag.
  2. The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.
  3. When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.
  4. When deploying the airbag, perform the operation at least 10 m (33 ft) away from the curtain shield airbag assembly.
  5. The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
  6. Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.
  7. Do not apply water, etc. to a curtain shield airbag assembly with a deployed airbag.
  8. Always wash your hands with water after completing the operation.


1. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY LH (WHEN INSTALLED IN VEHICLE)

HINT:
Prepare a battery as the power source to deploy the airbag.

  1. B104819E01
    Check the function of SST (Click here).

  1. Precaution (Click here).

  1. Disconnect the cable from the negative battery terminal.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.

  1. Remove the roof headlining.

    HINT:
    Refer to the procedures up to "REMOVE ROOF HEADLINING" (Click here).

  1. Install SST.

    1. C128225E01
      Disconnect the connector from the curtain shield airbag assembly.

      NOTICE:
      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. C128226E01
      Connect the SST connector to the curtain shield airbag assembly.
      SST
      09082-00700  
      09082-00760  

      NOTICE:
      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.

    3. C110501E01
      Move SST at least 10 m (33 ft) away from the vehicle side window.

    4. Securing enough clearance for the SST wire harness in the side window, close all doors and windows of the vehicle.

      NOTICE:
      Take care not to damage the SST wire harness.

    5. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

  1. Deploy the airbag.

    1. Check that no one is inside the vehicle or within a 10 m (33 ft) radius of the vehicle.

    2. Press the SST activation switch and deploy the airbag.

      CAUTION:
      1. When deploying the airbag, make sure that no one is near the vehicle.
      2. The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
      3. Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.
      4. Do not apply water, etc. to a curtain shield airbag assembly with a deployed airbag.
      5. Always wash your hands with water after completing the operation.

      HINT:
      The airbag is deployed as the LED of the SST activation switch comes on.


2. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY LH (WHEN NOT INSTALLED IN VEHICLE)

NOTICE:
  1. When disposing of the curtain shield airbag assembly, never use the customer's vehicle to deploy the airbag.
  2. Be sure to follow the procedure detailed below when deploying the airbag.

HINT:
Prepare a battery as the power source to deploy the airbag.

  1. B104819E01
    Check the function of SST (Click here).

  1. Remove the curtain shield airbag assembly (Click here).

    CAUTION:
    When removing the curtain shield airbag assembly, work must be started 90 seconds after the ignition switch is turned to the "LOCK" position and the negative (-) terminal cable is disconnected from the battery.

  1. C128227
    Cut off the deployment section of the curtain shield airbag assembly.

  1. B104882E01
    Using a service-purpose wire harness for the vehicle, tie down the curtain shield airbag assembly to the tire.
    Stripped wire harness section: 
    Area
    Measurement
    A
    1.25 mm2 or more (0.0019 in.2 or more)

    CAUTION:
    If the wire harness is too thin or any other object is used to tie down the curtain shield airbag assembly, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross section of at least 1.25 mm2 (0.0019 in.2).

    HINT:
    To calculate the area of the stripped wire harness section:
    Area = 3.14 x (Diameter)2 divided by 4


    1. C128228E01
      Position the curtain shield airbag assembly inside the tire as shown in the illustration.
      Must exceed the following dimensions.
      Tire size: 
      Area
      Measurement
      Width
      185 mm (7.28 in.)
      Inner diameter
      360 mm (14.17 in.)

      CAUTION:
      Make sure that the wire harness is tight. If there is slack in the wire harness, the curtain shield airbag assembly may become loose due to the shock when the airbag is deployed.

      NOTICE:
      The tire will be damaged by airbag deployment, so use waste tires.

  1. Install SST.

    1. C128229E01
      Connect the SST connector to the curtain shield airbag assembly.
      SST
      09082-00760  

  1. Place the tires.

    CAUTION:
    Do not face the deployment direction of the curtain shield airbag assembly toward the ground.


    1. C128230E01
      Place at least 2 tires under the tire to which the curtain shield airbag assembly is tied.

    2. Place at least 2 tires over the tire to which the curtain shield airbag assembly is tied. The top tire should have a disc wheel installed.

      NOTICE:
      Do not place the SST connector under the tire because it could be damaged.

    3. B105087
      Tie the tires together with 2 wire harnesses.

      CAUTION:
      Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.

  1. Install SST.

    1. C128231E01
      Connect SST connector.
      SST
      09082-00700  

      NOTICE:
      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

    2. Move SST at least 10 m (33 ft) away from the airbag tied down to the tires.

  1. Deploy the airbag.

    1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    2. Check that no one is within a 10 m (33 ft) radius of the tire to which the curtain shield airbag assembly is tied.

    3. Press the SST activation switch and deploy the airbag.

      CAUTION:
      When deploying the airbag, make sure that no one is near the tires.

      HINT:
      The airbag is deployed as the LED of the SST activation switch comes on.

  1. C128232
    Dispose of the curtain shield airbag assembly.

    CAUTION:
    1. The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
    2. Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.
    3. Do not apply water, etc. to a curtain shield airbag assembly with a deployed airbag.
    4. Always wash your hands with water after completing the operation.


    1. Remove the curtain shield airbag assembly from the tire.

    2. Place the curtain shield airbag assembly in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.

← INSTALLATION (from Aug 2012)DISPOSAL (Nov 2010 – Jul 2012) →