2011-2016 FJ Cruiser · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built Jul 2007 – Nov 2007

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal causes a current to flow to the coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.
If the ignition switch is turned OFF, the ECM holds the EFI relay ON for a maximum of 2 seconds to allow for the initial setting of the throttle valve.

WIRING DIAGRAM

A133430E01

INSPECTION PROCEDURE


1. INSPECT ECM (+B VOLTAGE)
G100798E08
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the E47 and B3 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    +B (E47-1) - E1 (B3-1)
    11 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
NG


2. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
G035617E11
  1. Disconnect the B3 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    E1 (B3-1) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (IGSW VOLTAGE)
G100798E09
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the E47 and B3 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    IGSW (E47-9) - E1 (B3-1)
    11 to 14 V



OK
Go to step 6
NG


4. CHECK FUSE (IGN FUSE)
A133441E05
  1. Remove the IGN fuse from the driver side junction block.

  1. Check the IGN fuse resistance.

    Standard Resistance:
    Below 1 Ω

  1. Reinstall the IGN fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


5. INSPECT IGNITION SWITCH
A056879E34
  1. Disconnect the A1 ignition switch connector.

  1. Check the resistance.

    Standard Resistance:
    Tester Connections
    Ignition Switch Positions
    Specified Conditions
    All Terminals
    LOCK
    10 kΩ or higher
    2 - 4
    ACC
    Below 1 Ω
    1 - 2, 1 - 4, 5 - 6
    ON
    1 - 3, 1 - 4, 3 - 4, 5 - 6, 5 - 7, 6 - 7
    START

  1. Reconnect the ignition switch connector.



NG
REPLACE IGNITION SWITCH (Click here)
OK

CHECK AND REPLACE HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM)

6. INSPECT ECM (MREL VOLTAGE)
G100798E10
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the B3 and E47 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    MREL (E47-8) - E1 (B3-1)
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


7. CHECK FUSE (EFI FUSE)
A133436E06
  1. Remove the EFI fuse from the engine room relay block.

  1. Check the EFI fuse resistance.

    Standard Resistance:
    Below 1 Ω

  1. Reinstall the EFI fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


8. INSPECT EFI RELAY
B016200E02
  1. Remove the EFI relay from the engine room relay block.

  1. Check the EFI relay resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    3 - 5
    10 kΩ or higher
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)

  1. Reinstall the EFI relay.



NG
REPLACE EFI RELAY
OK


9. CHECK HARNESS AND CONNECTOR (EFI RELAY- ECM, EFI RELAY - BODY GROUND)
A133471E03
  1. Check the harness and connector between the EFI relay and ECM.

    1. Remove the EFI relay from the engine room relay block.

    2. Disconnect the E47 ECM connector.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      EFI relay (1) - MREL (E47-8)
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      EFI relay (1) or MREL (E47-8) - Body ground
      10 kΩ or higher

    4. Reinstall the EFI relay.

    5. Reconnect the ECM connector.

  1. Check the harness and connector between the EFI relay and body ground.

    1. Remove the EFI relay from the engine room relay block.

    2. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      EFI relay (2) - Body ground
      Below 1 Ω

    3. Reinstall the EFI relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TERMINAL +B OF ECM - BATTERY POSITIVE TERMINAL)


← P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (+ P2A03) (from Nov 2010)ECM Power Source Circuit (Dec 2007 – Jul 2009) →