2011-2016 FJ Cruiser · Service Manual ENGINE

P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Nov 2010

Also covers:

Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

HINT:
  1. DTC P2A00 indicates malfunctions related to the bank 1 A/F sensor.
  2. DTC P2A03 indicates malfunctions related to the bank 2 A/F sensor.
  3. Bank 1 refers to the bank that includes cylinder No. 1.
  4. Bank 2 refers to the bank that includes cylinder No. 2.
  5. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

Refer to DTC P2195 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2A00
P2A03
Calculated value for air fuel ratio (A/F) sensor response rate deterioration level is less than threshold
(2 trip detection logic)
  1. A/F sensor
  2. A/F sensor heater
  3. ECM

MONITOR DESCRIPTION

After engine is warmed up, the ECM performs air-fuel ratio feedback control to maintain the air-fuel ratio at the stoichiometric level. In addition, active A/F control is performed for approximately 10 seconds after preconditions are met in order to measure the A/F sensor response rate. During active A/F control, the ECM forcibly increases and decreases the injection volume a certain amount, based on the stoichiometric air-fuel ratio learned during normal air-fuel ratio control, and measures the A/F sensor response rate. The ECM receives a signal from the A/F sensor while performing active A/F control and uses it to calculate the A/F sensor response rate deterioration level.
If the value for A/F sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and sets the DTC.
A115363E13

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation pattern will activate the A/F sensor response monitor.

A185027E07
  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester on.
  4. Clear the DTCs (Click here).
  5. Turn the ignition switch off and wait 30 seconds.
  6. Start the engine and warm it up (until the engine coolant temperature 75°C (167°F)). [A]
  7. Turn the tester on.
  8. Drive the vehicle at between 64 km/h and 120 km/h (40 mph and 75 mph) for 3 minutes. However, the vehicle should be driven at a constant speed. [B]

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
  10. Read the Pending DTCs.
  11. If a pending DTC is output, the system is malfunctioning.

    HINT:
    If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC P2A00 or P2A03.
  14. Check the DTC judgment result.
    Intelligent Tester 
    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or UNKNOWN, perform step [B] and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. (1) Connect the intelligent tester to the DLC3.
  2. (2) Start the engine.
  3. (3) Turn the tester on.
  4. (4) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  5. (5) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  6. (6) Perform the Control the Injection Volume for A/F sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  7. (7) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

    Standard:
    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS B1S1 or AFS B2S1
    (A/F)
    +25%
    Rich
    Less than 3.0 V
    AFS B1S1 or AFS B2S1
    (A/F)
    -12.5%
    Lean
    More than 3.35 V
    O2S B1S2 or O2S B2S2
    (HO2)
    +25%
    Rich
    More than 0.55 V
    O2S B1S2 or O2S B2S2
    (HO2)
    -12.5%
    Lean
    Less than 0.4 V

NOTICE:
The Air Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E01
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E01
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air fuel ratio extremely rich or lean)
  1. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor / A/F Control System / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2, then press View button.
  2. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.

HINT:
  1. DTC P2A00 or P2A03 may be also stored, when the air-fuel ratio is stuck rich or lean.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P2A00 and/or P2A03
    A
    P2A00 and/or P2A03 and other DTCs
    B

    HINT:
    If any DTCs other than P2A00 or P2A03 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E28
  1. Disconnect the A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (A/F Sensor)



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
  1. Disconnect the A/F sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B33-1 (HA1A) - B50-17 (HA1A)
    Always
    Below 1 Ω
    B31-1 (HA2A) - B50-19 (HA2A)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B33-1 (HA1A) or B50-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B31-1 (HA2A) or B50-19 (HA2A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P2A00 and/or P2A03
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


6. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


7. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    No output
    A
    P2A00 and/or P2A03
    B



B
REPLACE ECM (Click here)
A

END


← P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (+ P2A03) (Aug 2009 – Oct 2010)ECM Power Source Circuit (Jul 2007 – Nov 2007) →