B1800/51 Short in Driver Side Squib Circuit
Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010
Also covers:
- B1801/51 Open in Driver Side Squib Circuit
- B1802/51 Short to GND in Driver Side Squib Circuit
- B1803/51 Short to B+ in Driver Side Squib Circuit
Versions by build date: Jul 2007 – Oct 2010 from Nov 2010
DESCRIPTION
- The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.
- The circuit signals the SRS to deploy when deployment conditions are met.
- These DTCs are recorded when a malfunction is detected in the driver side squib circuit.
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| B1800/51 |
|
|
| B1801/51 |
|
|
| B1802/51 |
|
|
| B1803/51 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
- After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
| 1. CHECK CONNECTOR (DRIVER SIDE SQUIB - SPIRAL CABLE) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the steering pad.
Check the spiral cable connector and terminals (on the steering pad side) and check that the connector is properly connected to the steering pad.
- Result:
Result
Proceed to
No problem
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK STEERING PAD (DRIVER SIDE SQUIB) |
Disconnect the connectors from the steering pad.

Connect the white wire side of SST (resistance 2.1 Ω) to connector E (orange connector).
- CAUTION:
- Never connect a tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- Insert the SST straight into the terminals of the connector.
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- SST
- 09843-18061
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on, and wait for at least 60 seconds.
Turn the steering wheel lock to lock 5 times or more.
Check the DTCs (Click here).
- OK:
- DTC B1800/51, B1801/51, B1802/51 and B1803/51 are not output.
- HINT:
- DTCs other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 3. CHECK CONNECTOR (SPIRAL CABLE - INSTRUMENT PANEL WIRE) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector E.
Check the instrument panel wire connector and terminals (on the spiral cable side) and check that the connector is properly connected to the spiral cable.
- Result:
Result
Proceed to
No problem
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK SPIRAL CABLE |
Disconnect the instrument panel wire connector from the spiral cable.
Check for short to B+ in the circuit.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on.
Measure the voltage.
- Standard voltage:
Tester Condition
Switch Condition
Specified Condition
1 (D+) - Body ground
Ignition switch on
Below 1 V
2 (D-) - Body ground
Ignition switch on
Below 1 V
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Condition
Condition
Specified Condition
1 (D+) - 2 (D-)
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance.
- Standard resistance:
Tester Condition
Condition
Specified Condition
1 (D+) - Body ground
Always
1 MΩ or higher
2 (D-) - Body ground
Always
1 MΩ or higher
Check for short in the circuit.
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance.
- Standard resistance:
Tester Condition
Condition
Specified Condition
1 (D+) - 2 (D-)
Always
1 MΩ or higher
Restore the released activation prevention mechanism of connector D to the original condition.
|
|
||||
| OK | |
| 5. CHECK CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - INSTRUMENT PANEL WIRE) |
Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check the connector is properly connected to the center airbag sensor assembly.
- Result:
Result
Proceed to
No problem
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 6. CHECK INSTRUMENT PANEL WIRE |
Disconnect the instrument panel wire connector from the center airbag sensor assembly.
Check for short to B+ in the circuit.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on.
Measure the voltage.
- Standard voltage:
Tester Condition
Switch Condition
Specified Condition
1 (D+) -
Body ground
Ignition switch on
Below 1 V
2 (D-) -
Body ground
Ignition switch on
Below 1 V
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Condition
Condition
Specified Condition
1 (D+) - 2 (D-)
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance.
- Standard resistance:
Tester Condition
Condition
Specified Condition
1 (D+) -
Body ground
Always
1 MΩ or higher
2 (D-) -
Body ground
Always
1 MΩ or higher
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
- Standard resistance:
Tester Condition
Condition
Specified Condition
1 (D+) - 2 (D-)
Always
1 MΩ or higher
Restore the released activation prevention mechanism of connector B to the original condition.
|
|
||||
| OK | |
| 7. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the connectors to the steering pad, spiral cable and the center airbag sensor assembly.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1800/51, B1801/51, B1802/51 and B1803/51 are not output.
- HINT:
- DTCs other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
