2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1800/51 Short in Driver Side Squib Circuit

Diagnostic trouble codes · Vehicles built from Nov 2010

Also covers:

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

  1. The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.
  2. The circuit signals the SRS to deploy when deployment conditions are met.
  3. These DTCs are recorded when a malfunction is detected in the driver side squib circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B1800/51
  1. Center airbag sensor assembly detects line short circuit signal in driver side squib circuit 5 times during primary check.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1801/51
  1. Center airbag sensor assembly detects open circuit signal in driver side squib circuit for 2 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1802/51
  1. Center airbag sensor assembly detects short circuit to ground signal in driver side squib circuit for 0.5 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1803/51
  1. Center airbag sensor assembly detects short circuit to B+ signal in driver side squib circuit for 0.5 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C146254E77

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTOR (DRIVER SIDE SQUIB - SPIRAL CABLE)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the steering pad.

  1. Check the spiral cable connector and terminals (on the steering pad side) and check that the connector is properly connected to the steering pad.

    Result:
    Result
    Proceed to
    No problem
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE SPIRAL CABLE (Click here)

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK STEERING PAD (DRIVER SIDE SQUIB)

  1. H100853E03
    Disconnect the connectors from the steering pad.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector E (orange connector).

    CAUTION:
    Never connect a tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Turn the steering wheel lock to lock 5 times or more.

  1. Check the DTCs (Click here).

    OK:
    DTC B1800/51, B1801/51, B1802/51 and B1803/51 are not output.

    HINT:
    DTCs other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE STEERING PAD (Click here)

3. CHECK CONNECTOR (SPIRAL CABLE - INSTRUMENT PANEL WIRE)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector E.

  1. Check the instrument panel wire connector and terminals (on the spiral cable side) and check that the connector is properly connected to the spiral cable.

    Result:
    Result
    Proceed to
    No problem
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


4. CHECK SPIRAL CABLE
  1. Disconnect the instrument panel wire connector from the spiral cable.

  1. C127735E01
    Check for short to B+ in the circuit.
    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester Condition
      Switch Condition
      Specified Condition
      1 (D+) - Body ground
      Ignition switch on
      Below 1 V
      2 (D-) - Body ground
      Ignition switch on
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard resistance:
      Tester Condition
      Condition
      Specified Condition
      1 (D+) - 2 (D-)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester Condition
      Condition
      Specified Condition
      1 (D+) - Body ground
      Always
      1 MΩ or higher
      2 (D-) - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector D (Click here).

    2. Measure the resistance.

      Standard resistance:
      Tester Condition
      Condition
      Specified Condition
      1 (D+) - 2 (D-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector D to the original condition.



NG
REPLACE SPIRAL CABLE (Click here)
OK


5. CHECK CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - INSTRUMENT PANEL WIRE)
  1. Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check the connector is properly connected to the center airbag sensor assembly.

    Result:
    Result
    Proceed to
    No problem
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


6. CHECK INSTRUMENT PANEL WIRE
  1. Disconnect the instrument panel wire connector from the center airbag sensor assembly.

  1. H100856E16
    Check for short to B+ in the circuit.
    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester Condition
      Switch Condition
      Specified Condition
      1 (D+) -
      Body ground
      Ignition switch on
      Below 1 V
      2 (D-) -
      Body ground
      Ignition switch on
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard resistance:
      Tester Condition
      Condition
      Specified Condition
      1 (D+) - 2 (D-)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester Condition
      Condition
      Specified Condition
      1 (D+) -
      Body ground
      Always
      1 MΩ or higher
      2 (D-) -
      Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance.

      Standard resistance:
      Tester Condition
      Condition
      Specified Condition
      1 (D+) - 2 (D-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


7. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. H100855E01
    Connect the connectors to the steering pad, spiral cable and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1800/51, B1801/51, B1802/51 and B1803/51 are not output.

    HINT:
    DTCs other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1800/51 Short in Driver Side Squib Circuit (+ B1801/51, B1802/51, B1803/51) (Jul 2007 – Oct 2010)B1805/52 Short in Front Passenger Side Squib Circuit (+ B1806/52, B1807/52, B1808/52) (Jul 2007 – Oct 2010) →