SRS Warning Light Remains ON
Circuit diagnosis · Vehicles built from Aug 2008
DESCRIPTION
The SRS warning light is located on the combination meter assembly.When the SRS condition is normal, the SRS warning light illuminates for approximately 6 seconds after the ignition switch is turned from off to on, and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light illuminates or blinks to inform the driver of the problem. When terminals TC and CG of the DLC3 are connected, the SRS warning light blinks to indicate DTCs.
The center airbag sensor assembly is equipped with a voltage-increase circuit (DC-DC converter) in case the source voltage decreases. When the battery voltage decreases, the voltage-increase circuit (DC-DC converter) boosts the SRS voltage up to the normal level.
Malfunctions relating to battery voltage decreases cause the SRS warning light to illuminate, however, no DTCs are recorded in the center airbag sensor assembly. The SRS warning light goes off automatically when the source voltage returns to normal.
Signals to illuminate the SRS warning light are transmitted from the center airbag sensor assembly to the combination meter assembly.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.
- Turn the ignition switch off.
- Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
- Disconnect the connector from the center airbag sensor assembly.
- Disconnect the connectors from the steering pad.
- Disconnect the connectors from the front passenger airbag assembly.
- Disconnect the connector from the front seat outer belt assembly LH.
- Disconnect the connector from the front seat outer belt assembly RH.
- Disconnect the connector from the front seat side airbag assembly LH.
- Disconnect the connector from the front seat side airbag assembly RH.
- Disconnect the connector from the curtain shield airbag assembly LH.
- Disconnect the connector from the curtain shield airbag assembly RH.
| 1. CHECK BATTERY |
Measure the voltage of the battery.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
Battery
Always
11 to 14 V
|
|
||||
| OK | |
| 2. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - CENTER AIRBAG SENSOR ASSEMBLY) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the instrument panel wire connector from the center airbag sensor assembly.
Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.
- Result:
Result
Proceed to
No problem.
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 3. CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR) |
Disconnect the connector from the center airbag sensor assembly.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester connection
Switch Condition
Specified condition
E29-21 (IG2) -
E29-25 (E1)
Ignition switch ON
11 to 14 V
E29-21 (IG2) -
E29-26 (E2)
Ignition switch ON
11 to 14 V
|
|
||||
| OK | |
| 4. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - COMBINATION METER) |
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the instrument panel wire connector from the combination meter assembly.
Check the instrument panel wire connector and terminals (on the combination meter side) and check that the connector is properly connected to the combination meter assembly.
- Result:
Result
Proceed to
No problem.
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 5. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR ASSEMBLY - COMBINATION METER) |


Disconnect the connectors from the center airbag sensor assembly and combination meter assembly.
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E13-6 (SW) - Body ground
Ignition switch ON
Below 1 V
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E13-6 (SW) - E29-11 (LA)
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E13-6 (SW) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the instrument panel wire to the center airbag sensor assembly.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester connection
Condition
Specified condition
E13-6 (SW) - Body ground .
For 6 seconds after ignition switch turned ON.
Below 1 V
After 6 seconds have passed since ignition switch turned ON.
11 to 14 V
|
|
||||
| OK | ||
| ||
