2011-2016 FJ Cruiser · Service Manual RESTRAINTS

SRS Warning Light does not Come ON

Circuit diagnosis · Vehicles built from Aug 2008

DESCRIPTION

Click here.

WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE


1. CHECK BATTERY
  1. Measure the voltage of the battery.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Battery
    Always
    11 to 14 V



NG
CHECK AND REPLACE BATTERY OR CHARGING SYSTEM
OK


2. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - COMBINATION METER)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connector from the combination meter assembly.

  1. Check the instrument panel wire connector and terminals (on the combination meter side) and check that the connector is properly connected to the combination meter assembly.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


3. CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
  1. Disconnect the connector from the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. C192797E03
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-2 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E13-21 (ES) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connector from the center airbag sensor assembly.

  1. Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


5. CHECK INSTRUMENT PANEL WIRE
C192796E01
  1. Disconnect the connectors from the center airbag sensor assembly and combination meter assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E13-6 (SW) - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E13-6 (SW) - E29-11 (LA)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E13-6 (SW) - Body ground
      Always
      1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


6. CHECK SRS WARNING LIGHT
  1. Connect the connector to the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Check the SRS warning light condition.

    OK:
    The SRS warning light goes off after the primary check period and comes on again after approximately 10 seconds.

    HINT:
    The primary check period lasts for approximately 6 seconds after the ignition switch is turned on.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)


← SRS Warning Light Remains ON (from Aug 2008)TC and CG Terminal Circuit (from Aug 2008) →