2011-2016 FJ Cruiser · Service Manual RESTRAINTS

SRS Warning Light Remains ON

Circuit diagnosis · Vehicles built from Aug 2011

Versions by build date: Jul 2007 – Jul 2011 from Aug 2011

DESCRIPTION

The SRS warning light is located on the combination meter assembly.
When the SRS condition is normal, the SRS warning light illuminates for approximately 6 seconds after the ignition switch is turned from off to ON, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light illuminates or blinks to inform the driver of the problem. When terminals TC and CG of the DLC3 are connected, the SRS warning light blinks to indicate DTCs.
The center airbag sensor assembly is equipped with a voltage-increase circuit (DC-DC converter) in case the source voltage decreases. When the battery voltage decreases, the voltage-increase circuit (DC-DC converter) boosts the SRS voltage up to the normal level.
Malfunctions relating to battery voltage decreases cause the SRS warning light to illuminate. However, no DTCs are recorded in the center airbag sensor assembly. The SRS warning light turns off automatically when the source voltage returns to normal.
Signals to illuminate the SRS warning light are transmitted from the center airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C246088E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. INSPECT BATTERY
  1. Measure the voltage of the battery.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Battery
    Always
    11 to 14 V



NG
CHECK AND REPLACE BATTERY OR CHARGING SYSTEM
OK


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and combination meter assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3. CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR ASSEMBLY)

  1. C196985E06
    Disconnect the connector from the center airbag sensor assembly.

  1. Connect the cable to the negative battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E29-21 (IG2) - E29-25 (E1)
    Ignition switch ON
    11 to 14 V
    E29-21 (IG2) - E29-26 (E2)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPLACE HARNESS AND CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER ASSEMBLY)

  1. B255879E01
    Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the combination meter assembly.

  1. Connect the cable to the negative battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-2 (IG+) - E13-21 (ES)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK SRS WARNING LIGHT
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connector to the combination meter assembly.

  1. Connect the cable to the negative battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Check the SRS warning light condition.

    OK:
    The SRS warning light turns off after the primary check period and comes on again after approximately 10 seconds.

    HINT:
    The primary check period lasts for approximately 6 seconds after the ignition switch is turned to ON.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)


← SRS Warning Light Remains ON (Jul 2007 – Jul 2011)SRS Warning Light does not Come ON (Jul 2007 – Jul 2011) →