2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1653/35 Seat Position Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

The seat position sensor circuit consists of the center airbag sensor assembly and the seat position sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position sensor circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B1653/35
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in seat position sensor circuit for 2 seconds.
  2. Seat position sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No.2
  2. Front seat inner belt assembly LH
  3. Seat position sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM

C162307E03

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch to the lock position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connectors from the steering pad.
  5. Disconnect the connectors from the front passenger airbag assembly.
  6. Disconnect the connector from the front seat outer belt assembly LH
  7. Disconnect the connector from the front seat outer belt assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.

1. CHECK DTC (CENTER AIRBAG SENSOR ASSEMBLY)

  1. H100890E01
    Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK CONNECTOR CONNECTION CONDITION
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3. CHECK SEAT POSITION SENSOR CIRCUIT

  1. C127730E01
    Check for open in the circuit.
    1. Disconnect the connectors from the center airbag sensor assembly and the seat position sensor.

    2. Using a service wire, connect L1-14 (DSP+) and L1-13 (DSP-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance.

      Standard resistance:
      Terminal Connection
      Condition
      Specified Condition
      2 (LSP+) - 1 (LSP-)
      Always
      Below 1 Ω

  1. C127731E01
    Check for short in the circuit.
    1. Disconnect the service wire from connector B.

    2. Measure the resistance.

      Standard resistance:
      Terminal Connection
      Condition
      Specified Condition
      2 (LSP+) - 1 (LSP-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Terminal Connection
      Condition
      Specified Condition
      2 (LSP+) - Body ground
      Always
      1 MΩ or higher
      1 (LSP-) - Body ground
      Always
      1 MΩ or higher

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Terminal Connection
      Switch Condition
      Specified Condition
      2 (LSP+) - Body ground
      Ignition switch on
      Below 1 V
      1 (LSP-) - Body ground
      Ignition switch on
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.



NG
Go to step 7
OK


4. CHECK SEAT POSITION SENSOR
H100890E01
  1. Connect the connectors to the center airbag sensor assembly and the seat position sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE SEAT POSITION SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position sensor (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


6. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. H100890E01
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END

7. CHECK FLOOR WIRE NO.2

  1. H100891E02
    Check for open in the circuit.
    1. Disconnect the connectors from the front seat inner belt assembly (wire harness) and the floor wire No.2.

    2. Using a service wire, connect L1-14 (DSP+) and L1-13 (DSP-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      L17-2 (LSP+) -
      L17-4 (LSP-)
      Always
      Below 1 Ω

  1. H100894E02
    Check for short in the circuit.
    1. Disconnect the service wire from connector B.

    2. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      L17-2 (LSP+) -
      L17-4 (LSP-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      L17-2 (LSP+) -
      Body ground
      Always
      1 MΩ or higher
      L17-4 (LSP-) -
      Body ground
      Always
      1 MΩ or higher

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester connection
      Switch Condition
      Specified Condition
      L17-2 (LSP+) -
      Body ground
      Ignition switch on
      Below 1 V
      L17-4 (LSP-) -
      Body ground
      Ignition switch on
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.



NG
REPAIR OR REPLACE FLOOR WIRE NO.2
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)


← B1648/82 Front Passenger Side Satellite Sensor Bus Initialization Incomplete (Nov 2010 – Jul 2012)B1653/35 Seat Position Airbag Sensor Circuit Malfunction (Nov 2010 – Jul 2012) →