2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1653/35 Seat Position Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit.
  2. Front seat inner belt assembly RH malfunction*1
  3. Front seat inner belt assembly LH malfunction*2
  4. Seat position airbag sensor malfunction
  5. Center airbag sensor assembly malfunction
  1. Floor wire*1
  2. No. 2 floor wire*2
  3. Front seat inner belt assembly RH*1
  4. Front seat inner belt assembly LH*2
  5. Seat position airbag sensor
  6. Center airbag sensor assembly
  1. *1: for RHD
  2. *2: for LHD

WIRING DIAGRAM

C268579E01
C268579E02

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).


1. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    for LHD
    A
    for RHD
    B



B
Go to step 13
A


2. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and seat position airbag sensor. Also check that the connectors that link the No. 2 floor wire and front seat inner belt assembly LH are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and seat position airbag sensor. Also check that the connectors that link the No. 2 floor wire and front seat inner belt assembly LH are properly connected.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

  1. C268580E03
    Connect the connectors to the front seat inner belt assembly LH and No. 2 floor wire.

  1. Using a service wire, connect terminals 14 (LSP+) and 13 (LSP-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 9
OK


4. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
  1. Disconnect the service wire from connector B.

  1. C268605E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    1 (LSP-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 10
OK


5. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

  1. C268605E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 11
OK


6. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

  1. C268605E01
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    1 (LSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 12
OK


7. CHECK DTC

  1. C268581E01
    Connect the connectors to the center airbag sensor assembly and seat position airbag sensor.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly



NG
Go to step 8
OK

USE SIMULATION METHOD TO CHECK (Click here)

8. CHECK SEAT POSITION AIRBAG SENSOR

  1. C268581E01
    Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Replace the seat position airbag sensor with a known good one (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Return the seat position airbag sensor that was installed for testing to its original location (Click here).

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE SEAT POSITION AIRBAG SENSOR (Click here)

9. CHECK FLOOR WIRE (OPEN)

  1. C268582E04
    Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-2 (LSP+) - L17-4 (LSP-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector B.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    No. 2 Floor Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)

10. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C268871E03
    Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    L17-4 (LSP-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)

11. CHECK FLOOR WIRE (SHORT)
C268871E03
  1. Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-2 (LSP+) - L17-4 (LSP-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)

12. CHECK FLOOR WIRE (SHORT TO B+)

  1. C268871E03
    Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L17-2 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    L17-4 (LSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)

13. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and seat position airbag sensor. Also check that the connectors that link the floor wire and front seat inner belt assembly RH are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and seat position airbag sensor. Also check that the connectors that link the floor wire and front seat inner belt assembly RH are properly connected.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


14. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

  1. C268611E01
    Connect the connectors to the front seat inner belt assembly RH and floor wire.

  1. Using a service wire, connect terminals 13 (RSP+) and 12 (RSP-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (RSP+) - 1 (RSP-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 20
OK


15. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
  1. Disconnect the service wire from connector B.

  1. C268612E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (RSP+) - Body ground
    Always
    1 MΩ or higher
    1 (RSP-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 21
OK


16. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

  1. C268612E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (RSP+) - 1 (RSP-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 22
OK


17. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

  1. C268612E01
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (RSP+) - Body ground
    Ignition switch ON
    Below 1 V
    1 (RSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 23
OK


18. CHECK DTC

  1. C268929E01
    Connect the connectors to the center airbag sensor assembly and seat position airbag sensor.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly



NG
Go to step 19
OK

USE SIMULATION METHOD TO CHECK (Click here)

19. CHECK SEAT POSITION AIRBAG SENSOR

  1. C268929E01
    Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Replace the seat position airbag sensor with a known good one (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Return the seat position airbag sensor that was installed for testing to its original location (Click here).

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE SEAT POSITION AIRBAG SENSOR (Click here)

20. CHECK FLOOR WIRE (OPEN)

  1. C268613E04
    Disconnect the floor wire from the front seat inner belt assembly RH.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K15-2 (RSP+) - K15-4 (RSP-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector B.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly RH
    *4
    Floor wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

FRONT SEAT INNER BELT ASSEMBLY RH (Click here)

21. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C268872E03
    Disconnect the floor wire from the front seat inner belt assembly RH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K15-2 (RSP+) - Body ground
    Always
    1 MΩ or higher
    K15-4 (RSP-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly RH
    *4
    Floor wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

FRONT SEAT INNER BELT ASSEMBLY RH (Click here)

22. CHECK FLOOR WIRE (SHORT)
C268872E03
  1. Disconnect the floor wire from the front seat inner belt assembly RH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K15-2 (RSP+) - K15-4 (RSP-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly RH
    *4
    Floor wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

FRONT SEAT INNER BELT ASSEMBLY RH (Click here)

23. CHECK FLOOR WIRE (SHORT TO B+)

  1. C268872E03
    Disconnect the floor wire from the front seat inner belt assembly RH.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K15-2 (RSP+) - Body ground
    Ignition switch ON
    Below 1 V
    K15-4 (RSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly RH
    *4
    Floor wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

FRONT SEAT INNER BELT ASSEMBLY RH (Click here)


← B1653/35 Seat Position Airbag Sensor Circuit Malfunction (Nov 2010 – Jul 2012)B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (Jul 2007 – Oct 2010) →