2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1653/35 Seat Position Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

The seat position sensor circuit consists of the center airbag sensor assembly and the seat position sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1653/35
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in seat position sensor circuit for 2 seconds.
  2. Seat position sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. Driver side floor wire
  2. Front seat inner belt assembly (Driver Side)
  3. Seat position sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM

C162307E09
C162307E12

INSPECTION PROCEDURE


1. CHECK DTC (CENTER AIRBAG SENSOR ASSEMBLY)

  1. H100890E10
    Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *a
    Seat Position Sensor
    *b
    Center Airbag Sensor Assembly
    *c
    DLC3
    *d
    DTC 35



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK CONNECTOR CONNECTION CONDITION
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3. CHECK SEAT POSITION SENSOR CIRCUIT

  1. C127730E04
    Check for open in the circuit.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Seat Position Sensor
    *b
    Center Airbag Sensor Assembly
    *c
    Driver Side Floor Wire
    *d
    Front Seat Inner Belt Assembly
    (Wire Harness)
    *e
    Front view of wire harness connector
    (to Seat Position Sensor)
    *f
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *g
    Connector E
    *h
    Connector B
    *i
    Service Wire
    1. Disconnect the connectors from the center airbag sensor assembly and the seat position sensor.

    2. Using a service wire, connect 14 and 13 of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Terminal Connection
      Condition
      Specified Condition
      2 (LSP+) - 1 (LSP-)
      Always
      Below 1 Ω
      for RHD:
      Terminal Connection
      Condition
      Specified Condition
      2 (RSP+) - 1 (RSP-)
      Always
      Below 1 Ω

  1. C127731E02
    Check for short in the circuit.
    1. Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Terminal Connection
      Condition
      Specified Condition
      2 (LSP+) - 1 (LSP-)
      Always
      1 MΩ or higher
      for RHD:
      Terminal Connection
      Condition
      Specified Condition
      2 (RSP+) - 1 (RSP-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Terminal Connection
      Condition
      Specified Condition
      2 (LSP+) - Body ground
      Always
      1 MΩ or higher
      1 (LSP-) - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Terminal Connection
      Condition
      Specified Condition
      2 (RSP+) - Body ground
      Always
      1 MΩ or higher
      1 (RSP-) - Body ground
      Always
      1 MΩ or higher

  1. Check for short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD:
      Terminal Connection
      Switch Condition
      Specified Condition
      2 (LSP+) - Body ground
      Ignition switch ON
      Below 1 V
      1 (LSP-) - Body ground
      Ignition switch ON
      Below 1 V
      for RHD:
      Terminal Connection
      Switch Condition
      Specified Condition
      2 (RSP+) - Body ground
      Ignition switch ON
      Below 1 V
      1 (RSP-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Seat Position Sensor
      *b
      Center Airbag Sensor Assembly
      *c
      Front Seat Inner Belt Assembly
      (Wire Harness)
      *d
      Driver Side Floor Wire
      *e
      Front view of wire harness connector
      (to Seat Position Sensor)
      *f
      Connector E



NG
Go to step 7
OK


4. CHECK SEAT POSITION SENSOR
  1. Connect the connectors to the center airbag sensor assembly and the seat position sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE SEAT POSITION SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the seat position sensor (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


6. CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END

7. CHECK DRIVER SIDE FLOOR WIRE

  1. H100891E04
    Check for open in the circuit.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Seat Position Sensor
    *b
    Center Airbag Sensor Assembly
    *c
    Front Seat Inner Belt Assembly
    (Wire Harness)
    *d
    Driver Side Floor Wire
    *e
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly)
    *f
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *g
    Connector C
    *h
    Connector B
    *i
    Service Wire
    1. Disconnect the connectors from the front seat inner belt assembly (wire harness) and the driver side floor wire.

    2. Using a service wire, connect 14 and 13 of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L17-2 (LSP+) -
      L17-4 (LSP-)
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K15-2 (RSP+) -
      K15-4 (RSP-)
      Always
      Below 1 Ω

  1. H100894E04
    Check for short in the circuit.
    1. Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L17-2 (LSP+) -
      L17-4 (LSP-)
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K15-2 (RSP+) -
      K15-4 (RSP-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L17-2 (LSP+) -
      Body ground
      Always
      1 MΩ or higher
      L17-4 (LSP-) -
      Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K15-2 (RSP+) -
      Body ground
      Always
      1 MΩ or higher
      K15-4 (RSP-) -
      Body ground
      Always
      1 MΩ or higher

  1. Check for short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      L17-2 (LSP+) -
      Body ground
      Ignition switch on
      Below 1 V
      L17-4 (LSP-) -
      Body ground
      Ignition switch on
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      K15-2 (RSP+) -
      Body ground
      Ignition switch on
      Below 1 V
      K15-4 (RSP-) -
      Body ground
      Ignition switch on
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Seat Position Sensor
      *b
      Center Airbag Sensor Assembly
      *c
      Front Seat Inner Belt Assembly
      (Wire Harness)
      *d
      Driver Side Floor Wire
      *e
      Front view of wire harness connector
      (to Front Seat Inner Belt Assembly)
      *f
      Connector C



NG
REPLACE DRIVER SIDE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)


← B1653/35 Seat Position Airbag Sensor Circuit Malfunction (Jul 2007 – Oct 2010)B1653/35 Seat Position Airbag Sensor Circuit Malfunction (from Aug 2012) →