2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1653/35 Seat Position Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2008

DESCRIPTION

The seat position sensor circuit consists of the center airbag sensor assembly and the seat position sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position sensor circuit.
DTC No.
Detection Condition
Trouble Area
B1653/35
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in seat position sensor circuit for 2 seconds.
  2. Seat position sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat inner belt assembly LH
  3. Seat position sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM

H101463E07

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connectors from the steering pad.
  5. Disconnect the connectors from the front passenger airbag assembly.
  6. Disconnect the connector from the front seat outer belt assembly LH
  7. Disconnect the connector from the front seat outer belt assembly RH.
  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.

1. CHECK CONNECTOR CONNECTION CONDITION
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


2. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and the seat position airbag sensor.

  1. Check that the connectors (on the center airbag sensor assembly side and seat position airbag sensor side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


3. CHECK SEAT POSITION SENSOR CIRCUIT (CENTER AIRBAG SENSOR - SEAT POSITION AIRBAG SENSOR)
C192782E02
  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Terminal Connection
      Switch Condition
      Specified Condition
      2 (LSP+) - Body ground
      Ignition switch ON
      Below 1 V
      1 (LSP-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Disconnect the connectors from the center airbag sensor assembly and the seat position airbag sensor.

    2. Using a service wire, connect L23-9 (DSP+) and L23-17 (DSP-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Terminal Connection
      Condition
      Specified Condition
      2 (LSP+) - 1 (LSP-)
      Always
      Below 1 Ω

  1. Check for short in the circuit.

    1. Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Terminal Connection
      Condition
      Specified Condition
      2 (LSP+) - 1 (LSP-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Terminal Connection
      Condition
      Specified Condition
      2 (LSP+) - Body ground
      Always
      1 MΩ or higher
      1 (LSP-) - Body ground
      Always
      1 MΩ or higher



NG
Go to step 7
OK


4. CHECK SEAT POSITION AIRBAG SENSOR

  1. C192784E01
    Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


6. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C192784E01
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END

7. CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
C192783E02
  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester connection
      Switch Condition
      Specified Condition
      L17-2 (LSP+) -
      Body ground
      Ignition switch ON
      Below 1 V
      L17-4 (LSP-) -
      Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Disconnect the connectors from the front seat inner belt assembly (wire harness) and the No. 2 floor wire.

    2. Using a service wire, connect L23-9 (DSP+) and L23-17 (DSP-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      L17-2 (LSP+) -
      L17-4 (LSP-)
      Always
      Below 1 Ω

  1. Check for short in the circuit.

    1. Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      L17-2 (LSP+) -
      L17-4 (LSP-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      L17-2 (LSP+) -
      Body ground
      Always
      1 MΩ or higher
      L17-4 (LSP-) -
      Body ground
      Always
      1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)


← B1648/82 Front Passenger Side Satellite Sensor Bus Initialization Incomplete (from Aug 2008)B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (from Aug 2008) →