2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2008

DESCRIPTION

The driver side seat belt buckle switch circuit consists of the center airbag sensor assembly and the front seat inner belt assembly LH.
DTC B1655/37 is recorded when a malfunction is detected in the driver side seat belt buckle switch circuit.
DTC No.
Detection Condition
Trouble Area
B1655/37
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in driver side seat belt buckle switch LH circuit for 2 seconds.
  2. Front seat inner belt assembly LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat inner belt assembly LH
  3. Center airbag sensor assembly

WIRING DIAGRAM

C127718E03

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connectors from the steering pad.
  5. Disconnect the connectors from the front passenger airbag assembly.
  6. Disconnect the connector from the front seat outer belt assembly LH.
  7. Disconnect the connector from the front seat outer belt assembly RH.
  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.

1. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


2. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt LH.

  1. Check that the connectors (on the center airbag sensor assembly side and front seat inner belt LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


3. CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
C192785E02
  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester connection
      Switch Condition
      Specified Condition
      L17-1 (LBE+) - Body ground
      Ignition switch ON
      Below 1 V
      L17-3 (LBE-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.

    2. Using a service wire, connect L23-10 (DBE+) and L23-18 (DBE-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      L17-1 (LBE+) - L17-3 (LBE-)
      Always
      Below 1 Ω

  1. Check for short in the circuit.

    1. Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      L17-1 (LBE+) - L17-3 (LBE-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      L17-1 (LBE+) - Body ground
      Always
      1 MΩ or higher
      L17-3 (LBE-) - Body ground
      Always
      1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


4. CHECK FRONT SEAT INNER BELT ASSEMBLY LH
C192786E01
  1. Connect the connectors to the center airbag sensor assembly and the front seat inner belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly LH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


6. CHECK CENTER AIRBAG SENSOR ASSEMBLY
C192786E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END


← B1653/35 Seat Position Airbag Sensor Circuit Malfunction (from Aug 2008)B1661/44 Roll Over Cut Off Indicator Malfunction (from Aug 2008) →