2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Fuel Receiver Gauge Malfunction

Circuit diagnosis · Vehicles built Aug 2011 – Oct 2012

Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Oct 2012 from Nov 2012

DESCRIPTION

  1. The combination meter assembly controls the fuel receiver gauge in accordance with the resistance of the fuel sender gauge, which varies depending on the amount of fuel remaining in the fuel tank.

WIRING DIAGRAM

E210378E02

INSPECTION PROCEDURE


1. CONFIRM DTC OUTPUT
  1. Check DTC (Click here).

    Result 
    Result
    Proceed to
    DTC B1500 is not output
    A
    DTC B1500 is output
    B



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER OPERATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel receiver gauge
    EMPTY/ 1/2 /FULL
    Perform the test with the vehicle stopped and the engine idling.

    OK:
    Fuel receiver gauge indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3. INSPECT FUEL SENDER GAUGE ASSEMBLY

  1. Remove the fuel sender gauge assembly (Click here).B255873E01

Text in Illustration 
*a
Component without harness connected
(Fuel Sender Gauge Assembly)
-
-
  1. Check that the float moves smoothly between F and E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Float Level
    Float Position (mm (in.))
    Specified Condition
    1 - 2
    F
    181.9 to 177.9 (7.161 to 7.003)
    12.0 to 18.0 Ω
    1/2
    99.5 (3.917)
    212.5 Ω
    Warning
    32.3 (1.271)
    375.4 Ω
    E
    0 (0)
    405.0 to 415.0 Ω

  1. Reinstall the fuel sender gauge assembly.



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK


4. CHECK FUEL SUCTION PLATE SUB-ASSEMBLY

  1. E158805E09
    Remove the fuel suction plate sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Fuel Suction Plate Sub-assembly)
    *b
    Connector A
    *c
    Connector B

  1. Reinstall the fuel suction plate sub-assembly.



NG
REPLACE FUEL SUCTION PLATE SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION PLATE SUB-ASSEMBLY)
  1. Disconnect the E13 combination meter assembly connector.

  1. Disconnect the L5 fuel suction plate sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E13-16 (L) - L5-2 (FS)
    Always
    Below 1 Ω
    E13-16 (L) - Body ground
    Always
    10 kΩ or higher
    E13-5 (E3) - L5-3 (FE)
    Always
    Below 1 Ω
    E13-5 (E3) - Body ground
    Always
    10 kΩ or higher
    E13-21 (ES) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the fuel suction plate sub-assembly connector.

  1. Reconnect the combination meter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Fuel Receiver Gauge Malfunction (Nov 2010 – Jul 2011)Fuel Receiver Gauge Malfunction (from Nov 2012) →