Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM
Fuel Receiver Gauge Malfunction
Circuit diagnosis · Vehicles built from Nov 2012
Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Oct 2012 from Nov 2012
DESCRIPTION
The combination meter assembly controls the fuel receiver gauge in accordance with the resistance of the fuel sender gauge, which varies depending on the amount of fuel remaining in the fuel tank.
WIRING DIAGRAM
Refer to DTC B1500 (Click here ).
INSPECTION PROCEDURE
1. CONFIRM DTC OUTPUT
Check DTC (Click here ).
Result
Result
Proceed to
DTC B1500 is not output
A
DTC B1500 is output
B
B
A
2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER OPERATION)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Combination Meter
Tester Display
Test Part
Control Range
Diagnostic Note
Fuel Meter Operation
Fuel receiver gauge
EMPTY/ 1/2 /FULL
Perform the test with the vehicle stopped and the engine idling.
OK:
Fuel receiver gauge indication is normal.
NG
OK
3. SYSTEM CHECK
Check the vehicle specifications.
Result
Result
Proceed to
for Single Tank Type
A
for Double Tank Type
B
B
A
4. INSPECT FUEL SENDER GAUGE ASSEMBLY
Remove the fuel sender gauge assembly (Click here ).
Text in Illustration
*a
Component without harness connected (Fuel Sender Gauge Assembly)
-
-
Check that the float moves smoothly between E and F.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Float Level
Float Position (mm (in.))
Specified Condition
1 - 2
F
181.9 to 177.9 (7.161 to 7.003)
12.0 to 18.0 Ω
1/2
99.5 (3.917)
212.5 Ω
Warning
32.3 (1.271)
375.4 Ω
E
0 (0)
405.0 to 415.0 Ω
Reinstall the fuel sender gauge assembly (Click here ).
NG
OK
5. INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY
Remove the fuel suction plate sub-assembly (Click here ).
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
A-2 (FS) - B-2
Always
Below 1 Ω
A-3 (FE) - B-1
Always
Below 1 Ω
Text in Illustration
*a
Component without harness connected (Fuel Suction Plate Sub-assembly)
*b
Connector A
*c
Connector B
Reinstall the fuel suction plate sub-assembly (Click here ).
NG
REPLACE FUEL SUCTION PLATE SUB-ASSEMBLY (Click here )
OK
6. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION PLATE SUB-ASSEMBLY)
Disconnect the E13 combination meter assembly connector.
Disconnect the L5 fuel suction plate sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
E13-16 (L) - L5-2 (FS)
Always
Below 1 Ω
E13-16 (L) - Body ground
Always
10 kΩ or higher
E13-5 (E3) - L5-3 (FE)
Always
Below 1 Ω
E13-5 (E3) - Body ground
Always
10 kΩ or higher
E13-21 (ES) - Body ground
Always
Below 1 Ω
Reconnect the fuel suction plate sub-assembly connector.
Reconnect the combination meter assembly connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
7. INSPECT FUEL SUB-TANK FUEL SENDER GAUGE ASSEMBLY
Remove the fuel sub-tank fuel sender gauge assembly (Click here ).
Text in Illustration
*a
Component without harness connected (Fuel Sub-tank Fuel Sender Gauge Assembly)
-
-
Check that the float moves smoothly between E and F.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Float Level
Float Position (mm (in.))
Specified Condition
e1-1 (L) - e1-2 (E3)
F
214 (8.425)
6.5 to 8.5 Ω
1/2
91.9 (3.618)
114.5 to 126.9 Ω
E
0 (0)
199.2 to 204.2 Ω
Reinstall the fuel sub-tank fuel sender gauge assembly (Click here ).
NG
REPLACE FUEL SUB-TANK FUEL SENDER GAUGE ASSEMBLY (Click here )
OK
8. CHECK HARNESS AND CONNECTOR (FUEL SUB-TANK FUEL SENDER GAUGE -
COMBINATION METER ASSEMBLY, FUEL SUCTION PLATE SUB-ASSEMBLY
Disconnect the E13 combination meter assembly connector.
Disconnect the L5 fuel suction plate sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
e1-2 (E3) - E13-5 (E3)
Always
Below 1 Ω
e1-2 (E3) - Body ground
Always
10 kΩ or higher
e1-1 (L) - L5-3 (E)
Always
Below 1 Ω
e1-1 (L) - Body ground
Always
10 kΩ or higher
E13-22 (L) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
9. INSPECT FUEL SENDER GAUGE ASSEMBLY
Remove the fuel sender gauge assembly (Click here ).
Text in Illustration
*a
Component without harness connected (Fuel Sender Gauge Assembly)
-
-
Check that the float moves smoothly between E and F.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Float Level
Float Position (mm (in.))
Specified Condition
1 - 2
F
171.9 to 183.9 (6.768 to 7.240)
6.5 to 8.5 Ω
1/2
82.4 to 95.3 (3.244 to 3.752)
118.6 to 132.6 Ω
E
0 (0)
205.8 to 210.8 Ω
Reinstall the fuel sender gauge assembly (Click here ).
NG
OK
10. INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY
Remove the fuel suction plate sub-assembly (Click here ).
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
A-2 (FS) - B-2
Always
Below 1 Ω
A-3 (FE) - B-1
Always
Below 1 Ω
Text in Illustration
*a
Component without harness connected (Fuel Suction Plate Sub-assembly)
*b
Connector A
*c
Connector B
Reinstall the fuel suction plate sub-assembly (Click here ).
NG
REPLACE FUEL SUCTION PLATE SUB-ASSEMBLY (Click here )
OK
11. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION PLATE SUB-ASSEMBLY)
Disconnect the E13 combination meter assembly connector.
Disconnect the L5 fuel suction plate sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
E13-16 (L) - L5-2 (FS)
Always
Below 1 Ω
E13-16 (L) - Body ground
Always
10 kΩ or higher
E13-21 (ES) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK