2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P0818 Driveline Disconnect Switch Input Circuit

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

The ECM detects the signal from the No. 2 transfer indicator switch (Transfer neutral position switch).
This DTC indicates that the No. 2 transfer indicator switch remains ON.
DTC No.
DTC Detection Condition
Trouble Area
P0818
No. 2 transfer indicator switch remains ON while vehicle is running under following conditions for 30 seconds. (2 trip detection logic):
  1. Vehicle speed is 25.1 km/h (15.6 mph) or more.
  2. Transfer high and low shift lever position: H
  1. Short in No. 2 transfer indicator switch (Transfer neutral position switch) circuit
  2. No. 2 transfer indicator switch
  3. Combination meter
  4. ECM

MONITOR DESCRIPTION

The ECM detects whether or not the transfer high and low shift lever is in neutral by monitoring the signal from the No. 2 transfer indicator switch.
If the ECM detects that the transfer high and low shift lever is in neutral under the following conditions, the ECM will conclude that there is a malfunction of the No. 2 transfer indicator switch:
  1. No. 2 transfer indicator switch indicates that the transfer high and low shift lever is in neutral.
  2. Transfer high and low shift lever is in the H position.
  3. The vehicle is traveling at 25.1 km/h (15.6 mph) or more.
  4. The No. 2 transfer indicator switch has been ON for more than 30 seconds.
If all of the above conditions are detected, the ECM will conclude that there is a malfunction of the No. 2 transfer indicator switch, illuminate the MIL and store the DTC.

WIRING DIAGRAM

C130139E03

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - BODY GROUND)
G037538E08
  1. Disconnect the E82 connector of the ECM.

  1. Disconnect the No. 2 transfer indicator switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Transfer Connection
    Condition
    Specified Condition
    1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector:
    (to No. 2 Transfer Indicator Switch)



NG
Go to step 3
OK


2. INSPECT NO. 2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH)
G034535E03
  1. Remove the No. 2 transfer indicator switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch ball is pushed
    Below 1 Ω
    Switch ball is not pushed
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected:
    (No. 2 Transfer Indicator Switch)
    *a
    Push



NG
REPLACE NO. 2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH) (Click here)
OK

REPLACE ECM (Click here)

3. CHECK HARNESS AND CONNECTOR (COMBINATION METER - BODY GROUND)
  1. Disconnect the E14 connector of the combination meter.

  1. C130136E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Transfer Connection
    Condition
    Specified Condition
    E14-22 (A/T3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER (Click here)


← P0818 Driveline Disconnect Switch Input Circuit (Aug 2009 – Oct 2010)P0818 Driveline Disconnect Switch Input Circuit (from Aug 2012) →