2011-2016 FJ Cruiser · Service Manual RESTRAINTS

Front Passenger Side Seat Belt Warning Light Malfunction

Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

When the passenger seat belt is not fastened with the ignition switch ON and the passenger seat occupied, the passenger seat belt warning light display blinks. The occupant detection sensor detects if the passenger seat is occupied and sends signals to the combination meter assembly. The inner belt detects the passenger seat belt condition and sends signals to the combination meter assembly. After receiving the signals from the occupant detection sensor and inner belt, the combination meter assembly sends signals to the integration control and panel assembly to request the passenger seat belt warning light to blink or go off.

WIRING DIAGRAM

B168595E01

INSPECTION PROCEDURE


1. INSPECT FUSE (IG1)

  1. B168600E01
    Remove the IG1 fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IG1 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE (IG1)
OK


2. CHECK HARNESS AND CONNECTOR (POWER SOURCE, BODY GROUND)

  1. B168596E01
    Disconnect the E32 integration control and panel assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E32-1 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B32-20 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT

  1. B168601E01
    Check the front passenger seat belt warning light condition.
    1. Apply battery voltage to the connector according to the table below.

      OK:
      Connection
      Specified Condition
      Battery positive (+) → 1 (IG+)
      Battery negative (-) → 16 (PBEW) and 20 (GND)
      Seat belt warning light comes on



NG
REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SEAT BELT WARNING LIGHT - COMBINATION METER ASSEMBLY)

  1. B168597E01
    Disconnect the E13 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E13-7 (WRNP) - E32-16 (PBEW)
    Always
    Below 1 Ω
    E13-7 (WRNP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT FRONT SEAT INNER BELT ASSEMBLY RH (PASSENGER SIDE)
B168599E01
  1. Disconnect the K9 front seat inner belt assembly (passenger side) connector.

  1. Disconnect the occupant detection sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 (RBE-) - B-3
    Tongue plate fastened
    10 kΩ or higher
    Tongue plate unfastened
    Below 1 Ω
    A-3 (RBE-) - Body ground
    Always
    10 kΩ or higher
    B-3 - Body ground
    Always
    10 kΩ or higher
    A-2 (+) - B-1
    Always
    Below 1 Ω
    A-2 (+) or B-1 - Body ground
    Always
    10 kΩ or higher



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)
OK


6. INSPECT OCCUPANT DETECTION SENSOR
B156681E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Passenger seat is occupied
    Below 100 Ω
    1 - 3
    Passenger seat is not occupied
    1 MΩ or higher



NG
REPLACE OCCUPANT DETECTION SENSOR (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY)

  1. B168598E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E13-10 (PBKL) - K9-2 (+)
    Always
    Below 1 Ω
    E13-10 (PBKL) - Body ground
    Always
    10 kΩ or higher
    K9-3 (RBE-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Driver Side Seat Belt Warning Light does not Operate (from Nov 2010)Front Passenger Side Seat Belt Warning Light Malfunction (from Nov 2010) →