2011-2016 FJ Cruiser · Service Manual CRUISE CONTROL SYSTEM

P0571 Stop Light Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

The cruise control system cancels cruising when the ECM detects that the brake pedal is depressed during cruise control driving. The stop light switch assembly sends signals to the ECM according to the brake pedal conditions. When the brake pedal is released, terminal ST1- is the positive (+) battery voltage, and terminal STP voltage is below 1 V. While the brake pedal is depressed, terminal ST1- is below 1 V, and STP is positive (+) battery voltage. During braking, the ECM cancels cruise control as one of the manual cancel functions.
The ECM outputs this trouble code when the voltage of terminals ST1- and STP are both below 1 V for 0.5 seconds or more at the same time.
The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit.
DTC No.
DTC Detected Conditions
Trouble Areas
P0571
ECM detects a malfunction of the stop light switch circuit under both of the following conditions.
  1. Voltage of terminal STP is below 1 V for 0.5 seconds or more.
  2. Voltage of terminal ST1- is below 1 V for 0.5 seconds or more.
  1. Stop light switch assembly
  2. Stop light switch assembly circuit
  3. ECM

WIRING DIAGRAM

B133344E02

INSPECTION PROCEDURE


1. INSPECT STOP LIGHT SWITCH OPERATION
  1. Check that the stop lights come on while the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Brake Pedal Condition
    Stop Light Condition
    Depressed
    ON
    Released
    OFF



NG
INSPECT STOP LIGHT SWITCH CIRCUIT
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. I038520E05
    Disconnect the stop light switch assembly connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Switch Condition
    Stop Light Condition
    1 - 2
    Switch pin free
    (Brake pedal depressed)
    Below 1Ω
    3 - 4
    Switch pin free
    (Brake pedal depressed)
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    (Brake pedal released)
    10 kΩ or higher
    3 - 4
    Switch pin pushed in
    (Brake pedal released)
    Below 1Ω

  1. Reconnect the stop light switch assembly connector.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3. INSPECT ECM (STP SIGNAL)

  1. B133345E02
    Disconnect the E47 ECM connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    STP (E47-15) - Body ground
    Depressed
    11 to 14 V
    STP (E47-15) - Body ground
    Released
    Below 1V
    ST1- (E47-16) - Body ground
    Depressed
    Below 1V
    ST1- (E47-16) - Body ground
    Released
    11 to 14 V

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)


← P0500 Vehicle Speed Sensor Circuit Malfunction (+ P0503) (from Nov 2010)P0571 Stop Light Switch Circuit Malfunction (Aug 2009 – Oct 2010) →