2011-2016 FJ Cruiser · Service Manual SUSPENSION & AXLE

ADJUSTMENT

Removal / installation · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 Aug 2012 – Oct 2012 from Nov 2012

NOTICE:
For vehicles equipped with VSC, if the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

  1. Disconnect the negative (-) battery terminal for more than 2 seconds.
  2. Reconnect the negative (-) battery terminal.
  3. Perform zero point calibration of the yaw rate and deceleration sensor and test mode inspection (Click here).

1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold Tire Inflation Pressure:
    Tire Size
    Front Wheel
    kPa (kgf/cm2, psi)
    Rear Wheel
    kPa (kgf/cm2, psi)
    265/70R17 115S
    220 (2.2, 32)
    220 (2.2, 32)

  1. R003031
    Using a dial indicator, check the tire runout.

    Tire runout:
    3.0 mm (0.118 in.) or less


2. MEASURE VEHICLE HEIGHT

D028453E03

NOTICE:
Before inspecting the wheel alignment, check the vehicle height.

Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.
Text in Illustration 
*a
Front Side
*b
Rear Side

Measuring points:
A:
Ground clearance of front wheel center
B:
Ground clearance of adjustment cam bolt center
C:
Ground clearance of rear wheel center
D:
Ground clearance of lower control arm set bolt center

Standard Vehicle Height (Unloaded Vehicle):
Vehicle Model
A-B
C-D
GSJ15L-GKFSKY
88.4 mm (3.48 in.)
61.6 mm (2.43 in.)
GSJ15L-GKASKY
87.7 mm (3.45 in.)
61.9 mm (2.43 in.)
GSJ15L-GKASKV
87.7 mm (3.45 in.)
61.9 mm (2.43 in.)
GSJ15L-GKFSKV
86.8 mm (3.41 in.)
62.1 mm (2.44 in.)
GSJ15L-GKASKC
87.6 mm (3.45 in.)
62.6 mm (2.46 in.)
GSJ15R-GKASKN
88.8 mm (3.49 in.)
58.8 mm (2.31 in.)
GSJ15R-GKASKQ
87.1 mm (3.42 in.)
60.3 mm (2.37 in.)
GSJ15R-GKASKY
87.6 mm (3.45 in.)
58.7 mm (2.31 in.)

NOTICE:
The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.


3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

Z003382E25
  1. Install the camber-caster-kingpin gauge and position the front wheel on the wheel alignment tester.

    Text in Illustration 
    *1
    Wheel Alignment Tester
    *2
    Gauge

  1. Inspect the camber, caster and steering axis inclination.

    Camber, Caster and Steering Axis Inclination (Unloaded Vehicle):
    Vehicle Model
    Camber
    Caster
    Steering Axis Inclination
    GSJ15L-GKFSKY
    -0°23' to 0°37'
    (-0.38° to 0.62°)
    2°49' to 3°49'
    (2.82° to 3.82°)
    11°53' to 12°53'
    (11.88° to 12.88°)
    GSJ15L-GKASKY
    -0°22' to 0°38'
    (-0.37° to 0.63°)
    2°48' to 3°48'
    (2.80° to 3.80°)
    11°52' to 12°52'
    (11.86° to 12.86°)
    GSJ15L-GKASKV
    -0°22' to 0°38'
    (-0.37° to 0.63°)
    2°48' to 3°48'
    (2.80° to 3.80°)
    11°52' to 12°52'
    (11.86° to 12.86°)
    GSJ15L-GKFSKV
    -0°21' to 0°39'
    (-0.35° to 0.65°)
    2°47' to 3°47'
    (2.78° to 3.78°)
    11°51' to 12°51'
    (11.85° to 12.85°)
    GSJ15L-GKASKC
    -0°22' to 0°38'
    (-0.37° to 0.63°)
    2°48' to 3°48'
    (2.80° to 3.80°)
    11°52' to 12°52'
    (11.86° to 12.86°)
    GSJ15R-GKASKN
    -0°23' to 0°37'
    (-0.38° to 0.62°)
    2°49' to 3°49'
    (2.82° to 3.82°)
    11°53' to 12°53'
    (11.88° to 12.88°)
    GSJ15R-GKASKQ
    -0°21' to 0°39'
    (-0.35° to 0.65°)
    2°47' to 3°47'
    (2.78° to 3.78°)
    11°51' to 12°51'
    (11.85° to 12.85°)
    GSJ15R-GKASKY
    -0°21' to 0°39'
    (-0.36° to 0.64°)
    2°47' to 3°47'
    (2.79° to 3.79°)
    11°51' to 12°51'
    (11.85° to 12.85°)

    NOTICE:
    1. Perform the inspection while the vehicle is empty (without spare tires or tools on board).
    2. The tolerance for the difference between the left and right wheels is 30' (0.50°) or less for both the camber and caster.

    If the steering axis inclination is not as specified after the camber and caster have been correctly adjusted, recheck the steering knuckle and front wheel for distortion and slack.


4. ADJUST CAMBER AND CASTER

NOTICE:
Inspect the toe-in after the camber has been adjusted.

  1. Loosen the nut and bolt.

  1. Turn camber adjust cam No. 2 and the toe adjust cam and adjust the camber and the caster.

    HINT:
    Try to adjust the camber and caster to the central values.


    G020169E05
    Text in Illustration 
    *1
    Front Cam LH
    *2
    Front Cam RH
    *3
    Rear Cam LH
    *4
    Rear Cam RH
    *a
    Front of the Vehicle
    -
    -

  1. C223019E02
    How to read the adjustment chart (using examples).
    Text in Illustration 
    *1
    Caster
    *2
    Camber
    *a
    Calculated Value
    *b
    0 Point

    1. Measure the present alignment.

      Camber:
      0°20' (0.33°)

      Caster:
      3°20' (3.33°)

    2. Calculate the difference between the standard value (A) and the measured value (B) on the adjustment chart.

      Standard value:
      Camber:
      0°00' (0°)
      Caster:
      3°30' (3.5°)
      Formula:
      B - A = C
      Camber:
      0°00' - (0°20') = -0°20'
      Caster:
      3°20' - (3°30') = -0°10'

    3. As shown in the chart, read the distance from the marked point to 0 point, and adjust the front and/or rear adjusting cams accordingly.

      Toe Adjust Cam:
      -(Shorter) 2.8

      Camber Adjust Cam:
      -(Shorter) 1.8


      C223018E02
      Text in Illustration 
      *1
      Caster
      *2
      Camber
      *3
      Front Cam Gradation
      *4
      Rear Cam Gradation


5. INSPECT TOE-IN

SA03213E21
 
*a
Front of the Vehicle

Toe-in:
A+B
C-D
-0°05' to 0°15'
(-0.08° to 0.24°)
-1.0 to 3.0 mm
(-0.04 to 0.12 in.)

If the toe-in is not within the specified range, adjust it at the rack ends.

6. ADJUST TOE-IN
  1. Remove the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Turn the right and left rack ends uniformly to adjust the toe-in.

    HINT:
    Try to adjust the toe-in to the middle of the specified range.

  1. G020168
    Make sure that the lengths of the right and left rack ends are the same.

  1. Tighten the tie rod end lock nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }

  1. Place the boots on the seats and install the clips.

    HINT:
    Make sure that the boots are not twisted.


7. INSPECT WHEEL TURNING ANGLE

SA00028E20
  1. Turn the steering wheel fully, and measure the wheel turning angle.

    Text in Illustration 
    *a
    Inside
    *b
    Outside
    *c
    Front of the Vehicle

    Wheel Turning Angle (Unloaded Vehicle):
    Vehicle Model
    Inside Wheel
    Outside Wheel
    (Reference)
    GSJ15L-GKFSKY
    33° 9' (31° 9' to 34° 9')
    33.15° (31.15° to 34.15°)
    29°36'
    (29.60°)
    GSJ15L-GKASKY
    33°10' (31°10' to 34°10')
    33.16° (31.16° to 34.16°)
    29°37'
    (29.62°)
    GSJ15L-GKASKV
    33°10' (31°10' to 34°10')
    33.16° (31.16° to 34.16°)
    29°37'
    (29.62°)
    GSJ15L-GKFSKV
    33°10' (31°10' to 34°10')
    33.16° (31.16° to 34.16°)
    29°38'
    (29.64°)
    GSJ15L-GKASKC
    33°10' (31°10' to 34°10')
    33.16° (31.16° to 34.16°)
    29°37'
    (29.62°)
    GSJ15R-GKASKN
    33° 9' (31° 9' to 34° 9')
    33.15° (31.15° to 34.15°)
    29°36'
    (29.60°)
    GSJ15R-GKASKQ
    33°10' (31°10' to 34°10')
    33.16° (31.16° to 34.16°)
    29°38'
    (29.64°)
    GSJ15R-GKASKY
    33°10' (31°10' to 34°10')
    33.16° (31.16° to 34.16°)
    29°38'
    (29.63°)

    If the right and left turning angles of the inside and outside wheels are not within the specified ranges, check the right and left rack end lengths.


8. FRONT WHEELS FACING STRAIGHT AHEAD

9. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ VSC)

NOTICE:
Disconnect the negative (-) battery terminal for more than 2 seconds.


10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ VSC)

11. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION (w/ VSC)
(Click here)

12. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION (w/ VSC)
(Click here)
← ADJUSTMENT (Jul 2007 – Oct 2010)ADJUSTMENT (Aug 2012 – Oct 2012) →