ADJUSTMENT
Removal / installation · Vehicles built Aug 2012 – Oct 2012
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 Aug 2012 – Oct 2012 from Nov 2012
- NOTICE:
- For vehicles equipped with VSC, if the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
- Disconnect the negative (-) battery terminal for more than 2 seconds.
- Reconnect the negative (-) battery terminal.
- Perform zero point calibration of the yaw rate and deceleration sensor and test mode inspection (Click here).
| 1. INSPECT TIRES |
Check the tires for wear and proper inflation pressure.
- Cold Tire Inflation Pressure:
Tire Size
Front Wheel
kPa (kgf/cm2, psi)
Rear Wheel
kPa (kgf/cm2, psi)
265/70R17 115S
220 (2.2, 32)
220 (2.2, 32)
Using a dial indicator, check the tire runout.

- Tire runout:
- 3.0 mm (0.118 in.) or less
| 2. MEASURE VEHICLE HEIGHT |
![]() ![]() |
- NOTICE:
- Before inspecting the wheel alignment, check the vehicle height.
| *a |
Front Side |
| *b |
Rear Side |
- Measuring points:
- A:
- Ground clearance of front wheel center
- B:
- Ground clearance of adjustment cam bolt center
- C:
- Ground clearance of rear wheel center
- D:
- Ground clearance of lower control arm set bolt center
- Standard Vehicle Height (Unloaded Vehicle):
Vehicle Model
A-B
C-D
GSJ15L-GKFSKY
88.4 mm (3.48 in.)
61.6 mm (2.43 in.)
GSJ15L-GKASKY
87.7 mm (3.45 in.)
61.9 mm (2.43 in.)
GSJ15L-GKASKV
87.7 mm (3.45 in.)
61.9 mm (2.43 in.)
GSJ15L-GKFSKV
86.8 mm (3.41 in.)
62.1 mm (2.44 in.)
GSJ15L-GKASKC
87.6 mm (3.45 in.)
62.6 mm (2.46 in.)
GSJ15R-GKASKN
88.8 mm (3.49 in.)
58.8 mm (2.31 in.)
GSJ15R-GKASKQ
87.1 mm (3.42 in.)
60.3 mm (2.37 in.)
GSJ15R-GKASKY
87.6 mm (3.45 in.)
58.7 mm (2.31 in.)
- NOTICE:
- The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.
| 3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION |
![]() ![]() |
Install the camber-caster-kingpin gauge and position the front wheel on the wheel alignment tester.
Text in Illustration *1
Wheel Alignment Tester
*2
Gauge
Inspect the camber, caster and steering axis inclination.
- Camber, Caster and Steering Axis Inclination (Unloaded Vehicle):
Vehicle Model
Camber
Caster
Steering Axis Inclination
GSJ15L-GKFSKY
-0°23' to 0°37'
(-0.38° to 0.62°)
2°49' to 3°49'
(2.82° to 3.82°)
11°53' to 12°53'
(11.88° to 12.88°)
GSJ15L-GKASKY
-0°22' to 0°38'
(-0.37° to 0.63°)
2°48' to 3°48'
(2.80° to 3.80°)
11°52' to 12°52'
(11.86° to 12.86°)
GSJ15L-GKASKV
-0°22' to 0°38'
(-0.37° to 0.63°)
2°48' to 3°48'
(2.80° to 3.80°)
11°52' to 12°52'
(11.86° to 12.86°)
GSJ15L-GKFSKV
-0°21' to 0°39'
(-0.35° to 0.65°)
2°47' to 3°47'
(2.78° to 3.78°)
11°51' to 12°51'
(11.85° to 12.85°)
GSJ15L-GKASKC
-0°22' to 0°38'
(-0.37° to 0.63°)
2°48' to 3°48'
(2.80° to 3.80°)
11°52' to 12°52'
(11.86° to 12.86°)
GSJ15R-GKASKN
-0°23' to 0°37'
(-0.38° to 0.62°)
2°49' to 3°49'
(2.82° to 3.82°)
11°53' to 12°53'
(11.88° to 12.88°)
GSJ15R-GKASKQ
-0°21' to 0°39'
(-0.35° to 0.65°)
2°47' to 3°47'
(2.78° to 3.78°)
11°51' to 12°51'
(11.85° to 12.85°)
GSJ15R-GKASKY
-0°21' to 0°39'
(-0.36° to 0.64°)
2°47' to 3°47'
(2.79° to 3.79°)
11°51' to 12°51'
(11.85° to 12.85°)
- NOTICE:
- Perform the inspection while the vehicle is empty (without spare tires or tools on board).
- The tolerance for the difference between the left and right wheels is 30' (0.50°) or less for both the camber and caster.
- Perform the inspection while the vehicle is empty (without spare tires or tools on board).
| 4. ADJUST CAMBER AND CASTER |
- NOTICE:
- Inspect the toe-in after the camber has been adjusted.
Loosen the nut and bolt.
Turn camber adjust cam No. 2 and the toe adjust cam and adjust the camber and the caster.
- HINT:
- Try to adjust the camber and caster to the central values.


Text in Illustration *1
Front Cam LH
*2
Front Cam RH
*3
Rear Cam LH
*4
Rear Cam RH
*a
Front of the Vehicle
-
-
How to read the adjustment chart (using examples).

Text in Illustration *1
Caster
*2
Camber
*a
Calculated Value
*b
0 Point
Measure the present alignment.
- Camber:
- 0°20' (0.33°)
- Caster:
- 3°20' (3.33°)
Calculate the difference between the standard value (A) and the measured value (B) on the adjustment chart.
- Standard value:
- Camber:
- 0°00' (0°)
- Caster:
- 3°30' (3.5°)
- Formula:
- B - A = C
- Camber:
- 0°00' - (0°20') = -0°20'
- Caster:
- 3°20' - (3°30') = -0°10'
As shown in the chart, read the distance from the marked point to 0 point, and adjust the front and/or rear adjusting cams accordingly.
- Toe Adjust Cam:
- -(Shorter) 2.8
- Camber Adjust Cam:
- -(Shorter) 1.8


Text in Illustration *1
Caster
*2
Camber
*3
Front Cam Gradation
*4
Rear Cam Gradation
| 5. INSPECT TOE-IN |
![]() ![]() |
| *a |
Front of the Vehicle |
- Toe-in:
A+B
C-D
-0°05' to 0°15'
(-0.08° to 0.24°)
-1.0 to 3.0 mm
(-0.04 to 0.12 in.)
| 6. ADJUST TOE-IN |
Remove the rack boot set clips.
Loosen the tie rod end lock nuts.
Turn the right and left rack ends uniformly to adjust the toe-in.
- HINT:
- Try to adjust the toe-in to the middle of the specified range.
Make sure that the lengths of the right and left rack ends are the same.

Tighten the tie rod end lock nuts.
- Torque:
- 88 N*m{ 897 kgf*cm , 65 ft.*lbf }
Place the boots on the seats and install the clips.
- HINT:
- Make sure that the boots are not twisted.
| 7. INSPECT WHEEL TURNING ANGLE |
![]() ![]() |
Turn the steering wheel fully, and measure the wheel turning angle.
Text in Illustration *a
Inside
*b
Outside
*c
Front of the Vehicle
- Wheel Turning Angle (Unloaded Vehicle):
Vehicle Model
Inside Wheel
Outside Wheel
(Reference)
GSJ15L-GKFSKY
33° 9' (31° 9' to 34° 9')
33.15° (31.15° to 34.15°)
29°36'
(29.60°)
GSJ15L-GKASKY
33°10' (31°10' to 34°10')
33.16° (31.16° to 34.16°)
29°37'
(29.62°)
GSJ15L-GKASKV
33°10' (31°10' to 34°10')
33.16° (31.16° to 34.16°)
29°37'
(29.62°)
GSJ15L-GKFSKV
33°10' (31°10' to 34°10')
33.16° (31.16° to 34.16°)
29°38'
(29.64°)
GSJ15L-GKASKC
33°10' (31°10' to 34°10')
33.16° (31.16° to 34.16°)
29°37'
(29.62°)
GSJ15R-GKASKN
33° 9' (31° 9' to 34° 9')
33.15° (31.15° to 34.15°)
29°36'
(29.60°)
GSJ15R-GKASKQ
33°10' (31°10' to 34°10')
33.16° (31.16° to 34.16°)
29°38'
(29.64°)
GSJ15R-GKASKY
33°10' (31°10' to 34°10')
33.16° (31.16° to 34.16°)
29°38'
(29.63°)
| 8. FRONT WHEELS FACING STRAIGHT AHEAD |
| 9. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ VSC) |
- NOTICE:
- Disconnect the negative (-) battery terminal for more than 2 seconds.
| 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ VSC) |
| 11. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION (w/ VSC) |
| 12. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION (w/ VSC) |




