INSTALLATION
Removal / installation · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Oct 2012 from Nov 2012
| 1. INSTALL FRONT AXLE ASSEMBLY |
| 2. INSTALL FRONT UPPER SUSPENSION ARM |
![]() ![]() |
Install a new nut and a new clip.
- Torque:
- 110 N*m{ 1,122 kgf*cm , 81 ft.*lbf }
| 3. INSTALL FRONT LOWER BALL JOINT ATTACHMENT |
Install the front lower ball joint attachment with the 2 bolts.
- Torque:
- 160 N*m{ 1631 kgf*cm , 118 ft.*lbf }
| 4. INSTALL TIE ROD END SUB-ASSEMBLY |
![]() ![]() |
Install the tie rod end onto the steering knuckle.
Install the nut.
- Torque:
- 91 N*m{ 928 kgf*cm , 67 ft.*lbf }
Install a new cotter pin.
- NOTICE:
- If the holes in the cotter pin are not aligned, tighten the nut an additional 60°.
| 5. INSTALL FRONT STABILIZER LINK ASSEMBLY |
![]() ![]() |
Install the front stabilizer link assembly LH to the steering knuckle with the nut.
- Torque:
- 70 N*m{ 714 kgf*cm , 52 ft.*lbf }
- HINT:
- If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.
| 6. INSTALL FRONT AXLE HUB NUT |
Install the hub nut.
- Torque:
- 235 N*m{ 2396 kgf*cm , 174 ft.*lbf }
Install the adjusting lock cap and a new cotter pin.
| 7. INSPECT FRONT AXLE HUB BEARING |
![]() ![]() |
Inspect the axle hub backlash.
Using a dial indicator, check the backlash near the center of the axle hub.
- Maximum:
- 0.05 mm (0.0020 in.)
Inspect the axle hub runout.

Using a dial indicator, check the runout of the surface of the axle hub.
- Maximum:
- 0.05 mm (0.0020 in.)
| 8. INSTALL FRONT AXLE HUB GREASE CAP |
| 9. INSTALL FRONT SPEED SENSOR |
Type A:
Install the skid control sensor wire onto the steering knuckle with the bolt.
- Torque:
- 13 N*m{ 127 kgf*cm , 9 ft.*lbf }
Engage the 3 clamps.
Using a 5 mm hexagon wrench, install the speed sensor with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
Type B:
Install the skid control sensor wire onto the steering knuckle with the 2 bolts.
- Torque:
- 13 N*m{ 127 kgf*cm , 9 ft.*lbf }
Engage the clamp.
Install the speed sensor with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
| 10. INSTALL FRONT DISC |
Align the matchmarks of the disc and axle hub and install the disc.
- HINT:
- When replacing the disc, select the position that gives the minimum disc runout.
| 11. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY |
![]() ![]() |
Install the front disc brake caliper assembly with the 2 bolts.
- Torque:
- 123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }
Install the brake tube bracket onto the steering knuckle with the bolt.

- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
Using SST, install the brake tube onto the disc brake cylinder.

- SST
- 09023-00101
- Torque:
- for use without SST:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- for use with SST:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to the torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
| 12. INSTALL FRONT WHEEL |
- Torque:
- 112 N*m{ 1,137 kgf*cm , 82 ft.*lbf }
| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 3.9 N*m{ 40 kgf*cm , 35 in.*lbf }
| 14. BLEED BRAKE LINE |
Turn the ignition switch to ON.
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.
Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.
Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.
- Torque:
- 11 N*m{ 110 kgf*cm , 8 ft.*lbf }
Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.
With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.
- HINT:
- Air is bled as the pump motor operates while the brake pedal is being depressed.
- Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
- As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.
- Air is bled as the pump motor operates while the brake pedal is being depressed.
When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.
- Torque:
- 11 N*m{ 110 kgf*cm , 8 ft.*lbf }
Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.
Turn the ignition switch off.
Inspect for brake fluid leaks.
Check and adjust the brake fluid level (Click here).
Clear the DTCs (Click here).
| 15. CHECK VSC SENSOR SIGNAL |
| 16. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |





