2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN ENGINE COOLANT

A070279E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the service hole cover from the engine under cover.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.

  1. A076320E02
    Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Remove the radiator cap.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.


3. REMOVE V-BANK COVER

A126474
  1. Remove the 2 nuts, then remove the V-bank cover.


4. REMOVE AIR CLEANER ASSEMBLY

A075594E01
  1. Disconnect the No. 2 ventilation hose.

  1. A075595E01
    Disconnect the vacuum hose.

  1. Disconnect the mass air flow meter connector.

  1. Disengage the 2 wire harness clamps.

  1. A075596E01
    Loosen the 2 hose clamps.

  1. Remove the 2 bolts.

  1. Disconnect the air cleaner hose and remove the air cleaner.


5. REMOVE THROTTLE BODY BRACKET

  1. A126392
    Remove the 2 bolts and the throttle body bracket.


6. REMOVE OIL BAFFLE PLATE

  1. A126390
    Remove the bolt and the oil baffle plate.


7. REMOVE NO. 1 SURGE TANK STAY

  1. A126389
    Remove the 2 bolts and the No. 1 surge tank stay.


8. REMOVE NO. 2 SURGE TANK STAY

  1. A126391
    Remove the 2 bolts and the No. 2 surge tank stay.


9. REMOVE INTAKE AIR SURGE TANK

  1. A126395
    Disconnect the 2 water by-pass hoses.

  1. A126449
    Disconnect the fuel vapor feed hose.

  1. A075645
    Disconnect the ventilation hose.

  1. A075646E01
    Disconnect the 2 VSV connectors.

  1. Disconnect the throttle body with motor connector.

  1. Separate the 3 wire harness clamps and the hose clamp.

  1. A075648
    Remove the 2 nuts.

  1. Using a socket hexagon wrench 8, remove the 4 bolts, intake air surge tank and the gasket.


10. REMOVE IGNITION COIL ASSEMBLY

A126385E01
  1. For Bank 1:

    1. Disconnect the 3 connectors.

    2. Remove the 3 bolts, then remove the 3 ignition coils.

  1. A126386E01
    For Bank 2:

    1. Disconnect the 3 connectors.

    2. Remove the 3 bolts, then remove the 3 ignition coils.


11. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A072943E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


12. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

A076503E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


13. SET NO. 1 CYLINDER TO TDC/COMPRESSION

A076530E01
  1. Turn the crankshaft pulley until its groove and the "0" timing mark of the timing chain cover are aligned.

  1. G036289E04
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks above.

  1. G036271E01
    Place paint marks on the No. 1 chain links corresponding to the timing marks of the camshaft timing gears.


14. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.

  1. A076506E01
    Remove the 4 bolts, then remove the timing chain cover plate and gasket.

  1. A072958E02
    While turning the stopper plate of the tensioner upward, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner downward, insert a bar of φ3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

  1. Remove the 2 bolts, then remove the chain tensioner.


15. REMOVE NO. 2 CAMSHAFT

NOTICE:
Keep the camshaft level while it is being removed. The camshaft thrust clearance is very small and failing to keep it level could crack or damage the cylinder head journal surface, which receives the thrust force. This could subsequently lead the camshaft to seize or break. Perform the following steps to avoid such problems.

  1. G036272E01
    While raising the chain tensioner No. 2, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it.

  1. G036273E02
    Hold the hexagonal portion of the No. 2 camshaft with a wrench, and remove the camshaft timing gear set bolt.

    NOTICE:
    Be careful not to damage the cylinder head or valve lifter with the wrench.

  1. Separate the camshaft timing gear from the No. 2 camshaft.

  1. G036274E01
    Rotate the camshaft counterclockwise using the wrench so that the cam lobes of No. 1 cylinder face upward as shown in the illustration.

  1. A076510E05
    Using several steps, uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 4 bearing caps and No. 2 camshaft.


16. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

G036275E01
  1. Remove the No. 2 chain tensioner bolt, then remove the No. 2 chain tensioner and camshaft timing gear.


17. REMOVE CAMSHAFT

NOTICE:
Keep the camshaft level while it is being removed. The camshaft thrust clearance is very small and failing to keep it level could crack or damage the cylinder head journal surface, which receives the thrust force. This could subsequently lead the camshaft to seize or break. Perform the following steps to avoid such problems.

  1. G036276E01
    Hold the hexagonal portion of the No. 1 camshaft with a wrench, and loosen the camshaft timing gear set bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head or valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.

  1. G036277E01
    Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.

  1. G036278E01
    Rotate the No. 1 camshaft counterclockwise using the wrench so that the cam lobes of No. 1 cylinder face downward as shown in the illustration.

  1. A076515E05
    Using several steps, loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 4 bearing caps.

  1. G036279E01
    Remove the camshaft timing gear set bolt with the No. 1 camshaft lifted up, then remove the No. 1 camshaft and camshaft timing gear with No. 2 chain.

  1. A076517E01
    Tie the No. 1 chain with a piece of string as shown in the illustration.

    NOTICE:
    Be careful not to drop anything inside the timing chain cover.


18. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

NOTICE:
Keep the camshaft level while it is being removed. The camshaft thrust clearance is very small and failing to keep it level could crack or damage the cylinder head journal surface, which receives the thrust force. This could subsequently lead the camshaft to seize or break. Perform the following steps to avoid such problems.

  1. G036260E01
    While pushing down the No. 3 chain tensioner, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix it.

  1. G036261E01
    Hold the hexagonal portion of the No. 4 camshaft with a wrench, and remove the camshaft timing gear set bolt.

    NOTICE:
    Be careful not to damage the cylinder head or valve lifter with the wrench.

  1. Separate the camshaft timing gear from the No. 4 camshaft.

  1. A076482E04
    Using several steps, uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 4 bearing caps and No. 4 camshaft.


19. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

  1. G036262E02
    Remove the No. 3 chain tensioner bolt, then remove the No. 3 chain tensioner and camshaft timing gear.


20. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

NOTICE:
Keep the camshaft level while it is being removed. The camshaft thrust clearance is very small and failing to keep it level could crack or damage the cylinder head journal surface, which receives the thrust force. This could subsequently lead the camshaft to seize or break. Perform the following steps to avoid such problems.

  1. G036263E01
    Release the chain tension between the camshaft timing gear (bank 2) and crankshaft timing gear by turning the crankshaft pulley counterclockwise slightly.

  1. G036264E01
    Hold the hexagonal portion of the No. 3 camshaft with a wrench, then loosen the camshaft timing gear set bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head or valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.

  1. G036265E01
    Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.

  1. A076487E04
    Using several steps, uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 4 bearing caps.

  1. G036266E01
    Remove the camshaft timing gear set bolt with the No. 3 camshaft lifted up, then remove the No. 3 camshaft and camshaft timing gear with No. 2 chain.

  1. A076489E01
    Tie the No. 1 chain with a piece of string as shown in the illustration.

    NOTICE:
    Be careful not to drop anything inside the timing chain cover.

← COMPONENTS (from Aug 2014)REMOVAL (Aug 2009 – Oct 2010) →