2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743E01
    Unhook the engine under cover from the frame as shown in the illustration.
    Text in Illustration 
    *a
    Hook
    *b
    Frame


3. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the service hole cover from the engine under cover.

  1. A070279E03
    Install a vinyl hose to the radiator drain cock on the radiator assembly side.
    Text in Illustration 
    *a
    Vinyl Hose
    *b
    Tape

  1. Fix the vinyl hose with tape.

    A307922E01

    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Radiator Reserve Tank Cap Sub-assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly and drain the engine coolant.

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the engine coolant from the engine.

    NOTICE:
    If engine coolant is not drained from the radiator drain cock plug, cylinder block drain cock plug and radiator reservoir, clogging in the radiator assembly or engine coolant leakage from the seal of water pump may result.


5. REMOVE V-BANK COVER

  1. A229925E04
    Raise the front of the V-bank cover to disengage the 2 cushions of the V-bank cover from the 2 pins.
    Text in Illustration 
    *1
    Cushion
    *2
    Pin
    *3
    Hook
    *4
    No. 1 V-bank Cover Bracket

  1. Disengage the 2 hooks to remove the V-bank cover from the No. 1 V-bank cover bracket.


6. REMOVE AIR CLEANER CAP AND HOSE

  1. A227193
    Disconnect the MAF meter connector.

  1. Disengage the 4 wire harness clamps.

  1. Disconnect the ventilation hose and vacuum hose.

  1. Remove the bolt.

  1. Loosen the No. 1 air cleaner hose clamp.

  1. Release the 4 hinges.

  1. Remove the air cleaner cap and hose.


7. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


8. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A226753
    Remove the 3 bolts and the air cleaner case sub-assembly.


9. DISCONNECT NO. 1 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)

  1. A244710
    Slide the hose clip and disconnect the No. 1 air injection system hose from the air tube assembly.


10. REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

  1. A221459
    Remove the bolt to separate the air tube assembly from the timing chain cover sub-assembly.

  1. Slide the hose clip and disconnect the air tube assembly from the No. 1 emission control valve set.

  1. A221458
    Remove the 2 bolts to separate the air tube assembly from the timing chain cover sub-assembly and No. 1 surge tank stay.

  1. Slide the hose clip and disconnect the air tube assembly from the No. 2 emission control valve set.


11. REMOVE INTAKE AIR SURGE TANK

  1. A221456
    Disconnect the throttle body with motor assembly connector.

  1. Slide the 2 hose clips and disconnect the No. 4 water by-pass hose and No. 5 water by-pass hose from the water inlet housing.

  1. A221464
    Disengage the 2 clamps to separate the heater water hose from the intake air surge tank.

  1. A226749
    Disconnect the purge VSV connector.

  1. Slide the hose clip and disconnect the No. 1 fuel vapor feed hose from the purge VSV.

  1. A226750
    Slide the hose clip and disconnect the No. 1 ventilation hose from the intake air surge tank.

  1. A244712
    Remove the bolt to separate the wire harness clamp bracket from the No. 2 surge tank stay. (for RHD)

  1. Remove the 2 bolts and No. 2 surge tank stay from the intake air surge tank.

  1. A221461
    Disengage the clamp to separate the wire harness from the No. 1 surge tank stay.

  1. A221462
    Remove the 2 bolts and No. 1 surge tank stay from the intake air surge tank.

  1. A221460
    Remove the 2 bolts and throttle body bracket from the intake air surge tank.

  1. A221465E06
    Using an 8 mm socket hexagon wrench, remove the 4 bolts, 2 nuts and intake air surge tank from the intake manifold.
    Text in Illustration 
    *1
    Nut

  1. Remove the air surge tank to intake manifold gasket from the intake air surge tank.


12. REMOVE FAN SHROUD
(Click here)

13. REMOVE AIR TUBE (w/ Secondary Air Injection System)

  1. A288091
    Remove the 2 bolts, 2 nuts and air tube from the No. 1 emission control valve set and exhaust manifold sub-assembly RH.

  1. Remove the 2 gaskets from the air tube.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.


14. REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)

  1. A230693
    Remove the 2 bolts, 2 nuts and No. 2 air tube from the No. 2 emission control valve set and exhaust manifold sub-assembly LH.

  1. Remove the 2 gaskets from the No. 2 air tube.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.


15. REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A223568
    Disconnect the No. 1 emission control valve set connector.

  1. Slide the hose clip and disconnect the air tube assembly from the No. 1 emission control valve set.

  1. A223570
    Remove the 3 nuts and No. 1 emission control valve set from the cylinder head cover sub-assembly.


16. REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A223562
    Disconnect the No. 2 emission control valve set connector.

  1. Slide the hose clip and disconnect the air tube assembly from the No. 2 emission control valve set.

  1. A223564
    Remove the 3 nuts and No. 2 emission control valve set from the cylinder head cover sub-assembly LH.


17. REMOVE IGNITION COIL ASSEMBLY

  1. A226756
    Disconnect the 6 ignition coil assembly connectors.

  1. Remove the 6 bolts and 6 ignition coil assemblies from the cylinder head cover sub-assembly.


18. SEPARATE VANE PUMP ASSEMBLY

A225904
  1. Disconnect the 2 clamps and vane pump connector.

  1. Remove the 2 bolts and separate the vane pump.


19. REMOVE GENERATOR ASSEMBLY
(Click here)

20. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

A222114
  1. Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


21. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)

A225999
  1. Disconnect the 4 hoses.

  1. Remove the 3 bolts and water by-pass pipe.


22. REMOVE NO. 1 OIL PIPE

A223691
  1. Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.

  1. Remove the oil control valve filter LH and gaskets.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


23. REMOVE NO. 2 OIL PIPE

A223692
  1. Remove the 2 oil pipe unions, gaskets and No. 2 oil pipe.

  1. Remove the oil control valve filter RH and gaskets.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


24. REMOVE REAR CYLINDER HEAD COVER

  1. A224695
    Remove the 3 bolts and cover.


25. DISCONNECT FUEL PIPE SUB-ASSEMBLY
  1. Remove the 2 bolts and disconnect the fuel pipe.


26. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

A223666
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223665
    Remove the 3 gaskets.


27. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A223669
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223668
    Remove the 3 gaskets.


28. REMOVE TIMING CHAIN COVER PLATE

A224737
  1. Remove the 4 bolts, timing chain cover plate and gasket.


29. SET NO. 1 CYLINDER TO TDC/COMPRESSION

A072945E01
  1. Turn the crankshaft pulley, and align the notch with the "0" timing mark of the timing chain cover.

  1. A224754E02
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    Text in Illustration 
    *a
    for Bank 2
    *b
    for Bank 1
    *c
    Paint Mark

    HINT:
    If the marks are not aligned, turn the crankshaft again to align the marks.

  1. Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the No. 1 chain.

    HINT:
    Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.


30. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

A226510E01
  1. Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.

    HINT:
    This prevents the valves and pistons from interfering with each other.

  1. A226547E05
    Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of 1.27 mm (0.0500 in.) into the hole.
    Text in Illustration 
    *a
    Lever Hole
    *b
    Tensioner Hole

  1. A072945E01
    Turn the crankshaft clockwise, and align the notch with the timing mark "0" of the timing chain cover.

  1. A224739
    Remove the 2 bolts and chain tensioner.

    NOTICE:
    Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.


31. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

A226507E01
  1. Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain between the banks.

    HINT:
    When turning the crankshaft, engine oil may spray out of the oil holes.

    CAUTION:
    As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.

  1. A226508E01
    Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.

    HINT:
    When turning the crankshaft, engine oil may spray out of the oil holes.

  1. A224759
    Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.


32. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

A225726E03
  1. Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Replacement Bolt and Washer Installation

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number for replacement bolts: 91551-G0845 (8 bolts)
    3. Part number for replacement washers: 90201- 12028 (16 washers)

    NOTICE:
    1. Do not install the bearing caps when installing replacement bolts and washers.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow replacement bolts or washers to contact the camshaft.
    4. Do not drop replacement bolts or washers into the cylinder head.


33. REMOVE NO. 2 CAMSHAFT

A224761
  1. Remove the bolt of the No. 2 chain tensioner assembly.

  1. A224769
    Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.

  1. A224763
    While lifting up the No. 2 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


34. REMOVE CAMSHAFT
  1. Lift up the rear of the camshaft so that it is at an angle.

  1. A224767
    Remove the chain from the camshaft timing gear and pull out the camshaft and No. 2 chain towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain into the gap between the engine and cover.

  1. A224765
    Suspend the chain with a string or equivalent.


35. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)

A072945E01
  1. Turn the crankshaft counterclockwise, and align the notch with the "0" timing mark of the timing chain cover.

  1. A224760
    Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.


36. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

A225727E03
  1. Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Replacement Bolt and Washer Installation

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number for replacement bolts: 91551-G0845 (8 bolts)
    3. Part number for replacement washers: 90201- 12028 (16 washers)

    NOTICE:
    1. Do not install the bearing caps when installing replacement bolts and washers.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow replacement bolts or washers to contact the camshaft.
    4. Do not drop replacement bolts or washers into the cylinder head.


37. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

A224762
  1. Remove the bolt of the No. 3 chain tensioner assembly.

  1. A224770
    Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft.

  1. A224764
    While lifting up the No. 4 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


38. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
  1. Lift up the rear of the camshaft so that it is at an angle.

  1. A224768
    Remove the chain from the camshaft timing gear and pull out the No. 3 camshaft and No. 2 chain towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain into the gap between the engine and cover.

  1. A224766
    Suspend the chain with a string or equivalent.


39. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.

  1. A227959E08
    Remove the flange bolt and camshaft timing gear assembly.
    Text in Illustration 
    *1
    Straight Pin
    *2
    Flange Bolt
    *a
    Do Not Remove

    NOTICE:
    1. Do not remove the other 3 bolts.
    2. If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.


40. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.

  1. A227960E07
    Remove the flange bolt and camshaft timing exhaust gear assembly.
    Text in Illustration 
    *1
    Straight Pin
    *2
    Flange Bolt
    *a
    Do Not Remove

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.

← REMOVAL (Aug 2013 – Jul 2014)INSPECTION (Jul 2007 – Jul 2009) →