1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
2.
REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Remove the 4 bolts.
Unhook the engine under cover from the frame as shown in the illustration.
Text in Illustration
*a
Hook
*b
Frame
3.
DRAIN ENGINE OIL
Remove the oil filler cap.
Remove the oil pan drain plug and drain the engine oil into a container.
Install a new gasket and the oil pan drain plug.
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
4.
DRAIN ENGINE COOLANT
CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Remove the service hole cover from the engine under cover.
Install a vinyl hose onto the drain on the radiator side.
Text in Illustration
*1
Vinyl Hose
*2
Tape
Fix the vinyl hose with tape.
Text in Illustration
*1
Radiator Cap
*2
Reservoir Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug
Loosen the radiator drain cock plug.
Remove the radiator cap and drain the coolant.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
Loosen the 2 cylinder block drain cock plugs and drain the coolant from the engine.
NOTICE:
If coolant is not drained from the radiator drain cock plug, cylinder block drain cock plugs and radiator reservoir, clogging in the radiator or coolant leakage from the seal of water pump may result.
5.
REMOVE V-BANK COVER
Raise the front of the V-bank cover to disengage the 2 pins.
Remove the 2 V-bank cover hooks from the bracket.
Remove the V-bank cover.
Text in Illustration
*1
Pin
*2
Hook
6.
REMOVE AIR CLEANER CAP AND HOSE
Disconnect the MAF meter connector.
Disengage the 4 wire harness clamps.
Disconnect the ventilation hose and vacuum hose.
Remove the bolt.
Loosen the No. 1 air cleaner hose clamp.
Release the 4 hinges.
Remove the air cleaner cap and hose.
7.
REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
8.
REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Remove the 3 bolts and the air cleaner case sub-assembly.
9.
REMOVE INTAKE AIR SURGE TANK
Disconnect the No. 4 water by-pass hose.
Disconnect the No. 5 water by-pass hose.
Disconnect the throttle body connector.
Disconnect the No. 1 fuel vapor feed hose.
Disconnect the No. 1 vacuum switching valve connector.
Disconnect the No. 1 ventilation hose.
Disconnect the 2 heater water hose clamps.
Remove the 2 bolts and throttle body bracket.
Using a clip remover, disengage the wire harness clamp.
Remove the 2 bolts and No. 1 surge tank stay.
Remove the 2 bolts and No. 2 surge tank stay.
Remove the 2 nuts.
Text in Illustration
Nut
Using a 8 mm socket hexagon wrench, remove the 4 bolts and the intake air surge tank.
15.
REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)
Disconnect the 4 hoses.
Remove the 3 bolts and water by-pass pipe.
16.
REMOVE NO. 1 OIL PIPE
Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.
Remove the oil control valve filter LH and gaskets.
NOTICE:
Do not touch the mesh when removing the oil control valve filter.
17.
REMOVE NO. 2 OIL PIPE
Remove the 2 oil pipe unions, gaskets and No. 2 oil pipe.
Remove the oil control valve filter RH and gaskets.
NOTICE:
Do not touch the mesh when removing the oil control valve filter.
18.
REMOVE REAR CYLINDER HEAD COVER
Remove the 3 bolts and cover.
19.
DISCONNECT FUEL PIPE SUB-ASSEMBLY
Remove the 2 bolts and disconnect the fuel pipe.
20.
REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
21.
REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
22.
REMOVE TIMING CHAIN COVER PLATE
Remove the 4 bolts, timing chain cover plate and gasket.
23.
SET NO. 1 CYLINDER TO TDC/COMPRESSION
Turn the crankshaft pulley, and align the notch with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
Text in Illustration
*a
for Bank 2:
*b
for Bank 1:
*c
Paint Mark
HINT:
If the marks are not aligned, turn the crankshaft again to align the marks.
Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the No. 1 chain.
HINT:
Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.
24.
REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.
HINT:
This prevents the valves and pistons from interfering with each other.
Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of φ1.27 mm (0.0500 in.) into the hole.
Text in Illustration
*1
Lever Hole
*2
Tensioner Hole
Turn the crankshaft clockwise, and align the notch with the timing mark "0" of the timing chain cover.
Remove the 2 bolts and chain tensioner.
NOTICE:
Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.
25.
DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)
Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain between the banks.
HINT:
When turning the crankshaft, engine oil may spray out of the oil holes.
CAUTION:
As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.
Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.
HINT:
When turning the crankshaft, engine oil may spray out of the oil holes.
Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.
CAUTION:
As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.
26.
REMOVE CAMSHAFT BEARING CAP (for Bank 1)
Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.
Text in Illustration
*1
Bolt
*2
Washer
*a
Part Removal
*b
Replacement Bolt and Washer Installation
Torque:
10 N*m{
102 kgf*cm
, 7 ft.*lbf
}
HINT:
Arrange the removed parts so that they can be reinstalled in their original locations.
Part number for replacement bolts: 91551-G0845 (8 bolts)
Part number for replacement washers: 90201- 12028 (16 washers)
NOTICE:
Do not install the bearing caps when installing replacement bolts and washers.
Be sure to follow the numerical order when performing this procedure.
Do not allow replacement bolts or washers to contact the camshaft.
Do not drop replacement bolts or washers into the cylinder head.
27.
REMOVE NO. 2 CAMSHAFT
Remove the bolt of the No. 2 chain tensioner assembly.
Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.
While lifting up the No. 2 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.
28.
REMOVE CAMSHAFT
Lift up the rear of the camshaft so that it is at an angle.
Remove the chain from the camshaft timing gear and pull out the camshaft and No. 2 chain towards the rear of the vehicle to remove them.
NOTICE:
Do not drop the chain into the gap between the engine and cover.
Suspend the chain with a string or equivalent.
29.
DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)
Turn the crankshaft counterclockwise, and align the notch with the "0" timing mark of the timing chain cover.
Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.
CAUTION:
As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.
30.
REMOVE CAMSHAFT BEARING CAP (for Bank 2)
Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.
Text in Illustration
*1
Bolt
*2
Washer
*a
Part Removal
*b
Replacement Bolt and Washer Installation
Torque:
10 N*m{
102 kgf*cm
, 7 ft.*lbf
}
HINT:
Arrange the removed parts so that they can be reinstalled in their original locations.
Part number for replacement bolts: 91551-G0845 (8 bolts)
Part number for replacement washers: 90201- 12028 (16 washers)
NOTICE:
Do not install the bearing caps when installing replacement bolts and washers.
Be sure to follow the numerical order when performing this procedure.
Do not allow replacement bolts or washers to contact the camshaft.
Do not drop replacement bolts or washers into the cylinder head.
31.
REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY
Remove the bolt of the No. 3 chain tensioner assembly.
Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft.
While lifting up the No. 4 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.
32.
REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
Lift up the rear of the camshaft so that it is at an angle.
Remove the chain from the camshaft timing gear and pull out the No. 3 camshaft and No. 2 chain towards the rear of the vehicle to remove them.
NOTICE:
Do not drop the chain into the gap between the engine and cover.
Suspend the chain with a string or equivalent.
33.
REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
Fix the camshaft in place.
NOTICE:
Be careful not to damage the camshaft.
Remove the flange bolt and camshaft timing gear assembly.
Text in Illustration
*1
Straight Pin
*2
Flange Bolt
*a
Do Not Remove
NOTICE:
Do not remove the other 3 bolts.
If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.
34.
REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Fix the camshaft in place.
NOTICE:
Be careful not to damage the camshaft.
Remove the flange bolt and camshaft timing exhaust gear assembly.
Text in Illustration
*1
Straight Pin
*2
Flange Bolt
*a
Do Not Remove
NOTICE:
Be sure not to remove the other 4 bolts.
If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.