2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743E01
    Unhook the engine under cover from the frame as shown in the illustration.
    Text in Illustration 
    *a
    Hook
    *b
    Frame


3. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the service hole cover from the engine under cover.

  1. A070279E03
    Install a vinyl hose to the radiator drain cock on the radiator assembly side.
    Text in Illustration 
    *a
    Vinyl Hose
    *b
    Tape

  1. Fix the vinyl hose with tape.

    A307922E01

    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Radiator Reserve Tank Cap Sub-assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly and drain the engine coolant.

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the engine coolant from the engine.

    NOTICE:
    If engine coolant is not drained from the radiator drain cock plug, cylinder block drain cock plug and radiator reservoir, clogging in the radiator assembly or engine coolant leakage from the seal of water pump may result.


5. REMOVE V-BANK COVER

  1. A221454E02
    Raise the front of the V-bank cover to disengage the 2 pins.

  1. Remove the 2 V-bank cover hooks from the bracket.

  1. Remove the V-bank cover.

    Text in Illustration 
    *1
    Pin
    *2
    Hook


6. REMOVE AIR CLEANER CAP AND HOSE

  1. A227193
    Disconnect the MAF meter connector.

  1. Disengage the 4 wire harness clamps.

  1. Disconnect the ventilation hose and vacuum hose.

  1. Remove the bolt.

  1. Loosen the No. 1 air cleaner hose clamp.

  1. Release the 4 hinges.

  1. Remove the air cleaner cap and hose.


7. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


8. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A226753
    Remove the 3 bolts and the air cleaner case sub-assembly.


9. REMOVE INTAKE AIR SURGE TANK

  1. A226610
    Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.

  1. A226625
    Disconnect the throttle body connector.

  1. A226749
    Disconnect the No. 1 fuel vapor feed hose.

  1. Disconnect the No. 1 vacuum switching valve connector.

  1. A226750
    Disconnect the No. 1 ventilation hose.

  1. A221464
    Disconnect the 2 heater water hose clamps.

  1. A221460
    Remove the 2 bolts and throttle body bracket.

  1. A226751
    Using a clip remover, disengage the wire harness clamp.

  1. Remove the 2 bolts and No. 1 surge tank stay.

  1. A226752
    Remove the 2 bolts and No. 2 surge tank stay.

  1. A227191
    Remove the 2 nuts.
    Text in Illustration 
    V100136
    Nut

  1. Using a 8 mm socket hexagon wrench, remove the 4 bolts and the intake air surge tank.

  1. Remove the gasket.


10. REMOVE FAN SHROUD
  1. Remove the fan shroud (Click here).


11. REMOVE IGNITION COIL ASSEMBLY

  1. A226756
    Disconnect the 6 ignition coil connectors.

  1. Remove the 6 bolts and 6 ignition coils.


12. SEPARATE VANE PUMP ASSEMBLY

A225904
  1. Disconnect the 2 clamps and vane pump connector.

  1. Remove the 2 bolts and separate the vane pump.


13. REMOVE GENERATOR ASSEMBLY
  1. Remove the generator assembly (Click here).


14. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

A222114
  1. Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


15. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)

A225999
  1. Disconnect the 4 hoses.

  1. Remove the 3 bolts and water by-pass pipe.


16. REMOVE NO. 1 OIL PIPE

A223691
  1. Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.

  1. Remove the oil control valve filter LH and gaskets.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


17. REMOVE NO. 2 OIL PIPE

A223692
  1. Remove the 2 oil pipe unions, gaskets and No. 2 oil pipe.

  1. Remove the oil control valve filter RH and gaskets.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


18. REMOVE REAR CYLINDER HEAD COVER

  1. A224695
    Remove the 3 bolts and cover.


19. DISCONNECT FUEL PIPE SUB-ASSEMBLY
  1. Remove the 2 bolts and disconnect the fuel pipe.


20. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

A223666
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223665
    Remove the 3 gaskets.


21. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A223669
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223668
    Remove the 3 gaskets.


22. REMOVE TIMING CHAIN COVER PLATE

A224737
  1. Remove the 4 bolts, timing chain cover plate and gasket.


23. SET NO. 1 CYLINDER TO TDC/COMPRESSION

A072945E01
  1. Turn the crankshaft pulley, and align the notch with the "0" timing mark of the timing chain cover.

  1. A224754E02
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    Text in Illustration 
    *a
    for Bank 2:
    *b
    for Bank 1:
    *c
    Paint Mark

    HINT:
    If the marks are not aligned, turn the crankshaft again to align the marks.

  1. Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the No. 1 chain.

    HINT:
    Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.


24. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

A226510E01
  1. Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.

    HINT:
    This prevents the valves and pistons from interfering with each other.

  1. A226547E01
    Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of φ1.27 mm (0.0500 in.) into the hole.
    Text in Illustration 
    *1
    Lever Hole
    *2
    Tensioner Hole

  1. A072945E01
    Turn the crankshaft clockwise, and align the notch with the timing mark "0" of the timing chain cover.

  1. A224739
    Remove the 2 bolts and chain tensioner.

    NOTICE:
    Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.


25. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

A226507E01
  1. Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain between the banks.

    HINT:
    When turning the crankshaft, engine oil may spray out of the oil holes.

    CAUTION:
    As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.

  1. A226508E01
    Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.

    HINT:
    When turning the crankshaft, engine oil may spray out of the oil holes.

  1. A224759
    Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.


26. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

A225726E01
  1. Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Replacement Bolt and Washer Installation

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number for replacement bolts: 91551-G0845 (8 bolts)
    3. Part number for replacement washers: 90201- 12028 (16 washers)

    NOTICE:
    1. Do not install the bearing caps when installing replacement bolts and washers.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow replacement bolts or washers to contact the camshaft.
    4. Do not drop replacement bolts or washers into the cylinder head.


27. REMOVE NO. 2 CAMSHAFT

A224761
  1. Remove the bolt of the No. 2 chain tensioner assembly.

  1. A224769
    Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.

  1. A224763
    While lifting up the No. 2 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


28. REMOVE CAMSHAFT
  1. Lift up the rear of the camshaft so that it is at an angle.

  1. A224767
    Remove the chain from the camshaft timing gear and pull out the camshaft and No. 2 chain towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain into the gap between the engine and cover.

  1. A224765
    Suspend the chain with a string or equivalent.


29. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)

A072945E01
  1. Turn the crankshaft counterclockwise, and align the notch with the "0" timing mark of the timing chain cover.

  1. A224760
    Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.


30. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

A225727E01
  1. Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Replacement Bolt and Washer Installation

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number for replacement bolts: 91551-G0845 (8 bolts)
    3. Part number for replacement washers: 90201- 12028 (16 washers)

    NOTICE:
    1. Do not install the bearing caps when installing replacement bolts and washers.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow replacement bolts or washers to contact the camshaft.
    4. Do not drop replacement bolts or washers into the cylinder head.


31. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

A224762
  1. Remove the bolt of the No. 3 chain tensioner assembly.

  1. A224770
    Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft.

  1. A224764
    While lifting up the No. 4 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


32. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
  1. Lift up the rear of the camshaft so that it is at an angle.

  1. A224768
    Remove the chain from the camshaft timing gear and pull out the No. 3 camshaft and No. 2 chain towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain into the gap between the engine and cover.

  1. A224766
    Suspend the chain with a string or equivalent.


33. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.

  1. A227959E02
    Remove the flange bolt and camshaft timing gear assembly.
    Text in Illustration 
    *1
    Straight Pin
    *2
    Flange Bolt
    *a
    Do Not Remove

    NOTICE:
    1. Do not remove the other 3 bolts.
    2. If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.


34. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.

  1. A227960E02
    Remove the flange bolt and camshaft timing exhaust gear assembly.
    Text in Illustration 
    *1
    Straight Pin
    *2
    Flange Bolt
    *a
    Do Not Remove

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.

← REMOVAL (Aug 2011 – Jul 2013)REMOVAL (from Aug 2014) →