2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Taillight Relay Circuit

Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

The headlight dimmer switch sends a signal to the main body ECU.

WIRING DIAGRAM

E162318E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TAIL LIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Body / Active Test / Tail Light

  1. Check the taillights while operating the taillight relay using the tester.

    Body (Main Body ECU):
    Tester Display
    Test Part
    Control Range
    Normal Condition
    Tail Light
    Taillight Relay
    ON/OFF
    -

    OK:
    The taillights come on when operating it through the intelligent tester.

Result 
Result
Proceed to
OK
A
No illumination lights illuminate
B
Front clearance light does not illuminate
C
Taillight or license plate light does not illuminate
D
Outer rear view mirror illumination light does not illuminate*
E
*: w/ Outer rear view mirror illumination light


B
Go to step 2

C
Go to step 5

D
Go to step 7

E
Go to step 10
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT FUSE (TAIL FUSE)
  1. Remove the TAIL fuse from the main body ECU.

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    TAIL fuse
    Always
    Below 1 Ω

  1. Reinstall the TAIL fuse.



NG
REPLACE FUSE
OK


3. INSPECT TAIL RELAY
E109078E06
  1. Remove the TAIL relay from the main body ECU.

  1. Measure the resistance according value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Voltage is not applied between terminals 1 and 2
10 kΩ or higher
3 - 5
Apply the battery voltage between terminals 1 and 2
Below 1 Ω

  1. Reinstall the TAIL relay.



NG
REPLACE TAIL RELAY
OK


4. CHECK HARNESS AND CONNECTOR (BATTERY - TAIL RELAY)
B138193E02
  1. Remove the TAIL relay from the main body ECU.

  1. Measure the voltage according value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
1 - Body ground
Always
11 to 14 V
5 - Body ground
Always
11 to 14 V

  1. Reinstall the TAIL relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

5. INSPECT BULB (FRONT CLEARANCE LIGHT)
E162319E01
  1. w/o Headlight leveling:

    1. Remove the front turn signal lights (front clearance light).

    2. Apply battery voltage to the terminals and check that the front turn signal light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Front clearance light illuminates

    3. Reinstall the front turn signal lights.

  1. w/ Headlight leveling:

    1. Remove the front clearance lights.

    2. Apply battery voltage to the terminals and check that the front turn signal light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Front clearance light illuminates

    3. Reinstall the front clearance lights.

Result 
Result
Proceed to
OK
A
NG (w/o headlight beam level control system)
B
NG (w/ headlight beam level control system)
C


B
REPLACE BULB (Click here)

C
REPLACE BULB (Click here)
A


6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT CLEARANCE LIGHT)
E162320E01
  1. w/o Headlight leveling:

    1. Disconnect the A16 and A20 front turn signal light (front clearance light) connectors.

    2. Disconnect the 1B main body ECU connector.

    3. Measure the resistance according value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A16-1 - 1B-9
      Always
      Below 1 Ω
      A20-1 - 1B-11
      Always
      Below 1 Ω
      A16-1 or 1B-9 - Body ground
      Always
      10 kΩ or higher
      A20-1 or 1B-11 - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the front turn signal light (front clearance light) connectors.

    5. Reconnect the main body ECU connector.

  1. w/ Headlight leveling:

    1. Disconnect the A32 and A35 front clearance light connectors.

    2. Disconnect the 1B main body ECU connector.

    3. Measure the resistance according value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A35-1 - 1B-9
      Always
      Below 1 Ω
      A32-1 - 1B-11
      Always
      Below 1 Ω
      A35-1 or 1B-9 - Body ground
      Always
      10 kΩ or higher
      A32-1 or 1B-11 - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the front clearance light connectors.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT TURN SIGNAL LIGHT - BODY GROUND)

7. INSPECT BULB (TAILLIGHT)
B141038E04
  1. Remove the taillights.

  1. Apply battery voltage to the terminals and check that the taillight illuminates.

OK:
Measurement Condition
Specified Condition
Positive battery - Terminal 2
Negative battery - Terminal 1
Taillight illuminates

  1. Reinstall the taillights.



NG
REPLACE BULB (Click here)
OK


8. INSPECT BULB (LICENSE PLATE LIGHT)
E162321E01
  1. w/o Rear fog light:

    1. Remove the license plate light.

    2. Apply battery voltage to the terminals and check that the license plate light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 2
      Negative battery - Terminal 1
      License plate light illuminates

    3. Reinstall the license plate light.

  1. w/ Rear fog light:

    1. Remove the license plate light.

    2. Apply battery voltage to the terminals and check that the license plate light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      License plate light illuminates

    3. Reinstall the license plate light.

Result 
Result
Proceed to
OK
A
NG (w/o rear fog light)
B
NG (w/ rear fog light)
C


B
REPLACE BULB (Click here)

C
REPLACE BULB (Click here)
A


9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - TAILLIGHT, LICENSE PLATE LIGHT)
E162322E01
  1. w/o Rear fog light:

    1. Disconnect the L11 and L14 taillight connectors.

    2. Disconnect the S1 license plate light connector.

    3. Disconnect the 1F main body ECU connector.

    4. Measure the resistance according value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1F-13 - L11-2
      Always
      Below 1 Ω
      1F-13 - L14-2
      Always
      Below 1 Ω
      1F-13 - S1-2
      Always
      Below 1 Ω
      1F-13 or L11-2 or Body ground
      Always
      10 kΩ or higher
      1F-13 or L14-2 or Body ground
      Always
      10 kΩ or higher
      1F-13 or S1-2 or Body ground
      Always
      10 kΩ or higher

    5. Reconnect the taillight connectors.

    6. Reconnect the license plate light connector.

    7. Reconnect the main body ECU connector.

  1. w/ Rear fog light:

    1. Disconnect the L11 and L14 taillight connectors.

    2. Disconnect the N6 and N7 license plate light connectors.

    3. Disconnect the 1F main body ECU connector.

    4. Measure the resistance according value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1F-13 - L11-2
      Always
      Below 1 Ω
      1F-13 - L14-2
      Always
      Below 1 Ω
      1F-13 - N6-1
      Always
      Below 1 Ω
      1F-13 - N7-1
      Always
      Below 1 Ω
      1F-13 or L11-2 or Body ground
      Always
      10 kΩ or higher
      1F-13 or L14-2 or Body ground
      Always
      10 kΩ or higher
      1F-13 or N6-1 or Body ground
      Always
      10 kΩ or higher
      1F-13 or N7-1 or Body ground
      Always
      10 kΩ or higher

    5. Reconnect the taillight connectors.

    6. Reconnect the license plate light connectors.

    7. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TAILLIGHT, LICENSE PLATE LIGHT - BODY GROUND)

10. INSPECT BULB (OUTER REAR VIEW MIRROR ILLUMINATION LIGHT)
B138196E02
  1. Remove the outer rear view mirror assembly.

  1. Apply battery voltage to the terminals and check that the outer rear view mirror illumination light illuminates.

OK:
Measurement Condition
Specified Condition
Positive battery - Terminal 2
Negative battery - Terminal 1
Outer rear view mirror illumination light illuminates

  1. Reinstall the outer rear view mirror assembly.



NG
REPLACE BULB (Click here)
OK


11. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - OUTER REAR VIEW MIRROR ILLUMINATION LIGHT)
B138197E02
  1. Disconnect the H2 and G2 outer rear view mirror assembly connectors.

  1. Disconnect the 1L main body ECU connector.

  1. Measure the resistance according value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1L-5 - H2-2
Always
Below 1 Ω
1L-5 - G2-2
Always
Below 1 Ω

  1. Reconnect the outer rear view mirror assembly connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (OUTER REAR VIEW MIRROR ILLUMINATION LIGHT - BODY GROUND)


← Illumination Circuit (from Aug 2014)Taillight Relay Circuit (from Nov 2010) →