2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1820/55 Short in Front Driver Side - Side Squib Circuit

Diagnostic trouble codes · Vehicles built from Aug 2008

Also covers:

DESCRIPTION

The driver side - side squib circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH.
This circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side - side squib circuit.
DTC No.
Detection Condition
Trouble Area
B1820/55
  1. Center airbag sensor assembly detects line short circuit signal in driver side - side squib circuit 5 times during primary check.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly LH (Driver side - side squib)
  3. Center airbag sensor assembly
B1821/55
  1. Center airbag sensor assembly detects open circuit signal in driver side - side squib circuit for 2 seconds.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly LH (Driver side - side squib)
  3. Center airbag sensor assembly
B1822/55
  1. Center airbag sensor assembly detects short circuit to ground signal in driver side - side squib circuit for 0.5 seconds.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly LH (Driver side - side squib)
  3. Center airbag sensor assembly
B1823/55
  1. Center airbag sensor assembly detects short circuit to B+ signal in driver side - side squib circuit for 0.5 seconds.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat side airbag assembly LH (Driver side - side squib)
  3. Center airbag sensor assembly

WIRING DIAGRAM

H101823E25

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTOR (DRIVER SIDE -SIDE SQUIB - NO. 2 FLOOR WIRE)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the No.2 floor wire connector from the front seat side airbag assembly LH.

  1. Check the No. 2 floor wire connector and terminals (on the front seat side airbag assembly LH side) and check that the connector is properly connected to the front seat side airbag assembly LH.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE NO. 2 FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (DRIVER SIDE - SIDE SQUIB)

  1. C192800E01
    Disconnect the connector from the front seat side airbag assembly LH.

  1. Connect the black wire side of SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect a tester to the front seat side airbag assembly LH (driver side - side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1820/55, B1821/55, B1822/55 and B1823/55 are not output.

    HINT:
    DTCs other than DTC B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY LH (Click here)

3. CHECK CONNECTOR (NO. 2 FLOOR WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check the No. 2 floor wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE NO. 2 FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


4. CHECK NO. 2 FLOOR WIRE (DRIVER SIDE - SIDE SQUIB CIRCUIT)
C192801E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester connection
      Switch Condition
      Specified condition
      1 - Body ground
      Ignition switch ON
      Below 1 V
      2 - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified condition
      1 - 2
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified condition
      1 - Body ground
      Always
      1 MΩ or higher
      2 - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified condition
      1 - 2
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.



NG
REPLACE NO. 2 FLOOR WIRE
OK


5. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C192802E01
    Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1820/55, B1821/55, B1822/55 and B1823/55 are not output.

    HINT:
    DTCs other than DTC B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1815/54 Short in Front Passenger Side Squib 2nd Step Circuit (+ B1816/54, B1817/54, B1818/54) (from Aug 2008)B1825/56 Short in Front Passenger Side - Side Squib Circuit (+ B1826/56, B1827/56, B1828/56) (from Aug 2008) →