B1830/57 Short in Driver Side Curtain Shield Squib Circuit
Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012
Also covers:
- B1831/57 Open in Driver Side Curtain Shield Squib Circuit
- B1832/57 Short to GND in Driver Side Curtain Shield Squib Circuit
- B1833/57 Short to B+ in Driver Side Curtain Shield Squib Circuit
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012
DESCRIPTION
The driver side curtain shield squib circuit consists of the center airbag sensor assembly and the driver side - curtain shield airbag assembly.The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side curtain shield squib circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1830/57 |
|
|
| B1831/57 |
|
|
| B1832/57 |
|
|
| B1833/57 |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting Check Mode (signal check) with the intelligent tester (Click here).
- After selecting Check Mode (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting Check Mode (signal check) with the intelligent tester (Click here).
| 1. CHECK CONNECTORS (DRIVER SIDE FLOOR WIRE - DRIVER SIDE - CURTAIN SHIELD AIRBAG ASSEMBLY) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check the driver side floor wire connector and terminals (on the driver side - curtain shield airbag assembly side) and check that the connector is properly connected to the driver side - curtain shield airbag assembly.
Result Result
Proceed to
No problem.
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK DRIVER SIDE - CURTAIN SHIELD AIRBAG ASSEMBLY (DRIVER SIDE CURTAIN SHIELD SQUIB) |
Disconnect the connectors from the driver side - curtain shield airbag assembly.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.
- CAUTION:
- Never connect a tester to the driver side - curtain shield airbag assembly (driver side curtain shield squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- Insert the SST straight into the terminals of the connector.
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- SST
- 09843-18061
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1830/57, B1831/57, B1832/57 and B1833/57 are not output.
- HINT:
- DTCs other than DTC B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.
Text in Illustration *A
for LHD
*B
for RHD
*a
Driver Side Curtain Shield Squib
*b
Center Airbag Sensor Assembly
*c
Front view of wire harness connector
(to Driver Side - Curtain Shield Airbag Assembly)
*d
Connector C
*e
DLC3
*f
DTC 57
|
|
||||
| NG | |
| 3. CHECK CONNECTOR (DRIVER SIDE FLOOR WIRE - CENTER AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the SST from connector C.
Check the driver side floor wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.
Result Result
Proceed to
No problem.
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK DRIVER SIDE FLOOR WIRE (DRIVER SIDE CURTAIN SHIELD SQUIB CIRCUIT) |
Disconnect the connector from the center airbag sensor assembly.

Check for short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for LHD:
Tester Connection
Switch Condition
Specified Condition
L8-1 - Body ground
Ignition switch ON
Below 1 V
L8-2 - Body ground
Ignition switch ON
Below 1 V
- for RHD:
Tester Connection
Switch Condition
Specified Condition
K5-1 - Body ground
Ignition switch ON
Below 1 V
K5-2 - Body ground
Ignition switch ON
Below 1 V
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
L8-1 - L8-2
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
K5-1 - K5-2
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
L8-1 - Body ground
Always
1 MΩ or higher
L8-2 - Body ground
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
K5-1 - Body ground
Always
1 MΩ or higher
K5-2 - Body ground
Always
1 MΩ or higher
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
L8-1 - L8-2
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
K5-1 - K5-2
Always
1 MΩ or higher
Restore the released activation mechanism of connector B to the original condition.
Text in Illustration *A
for LHD
*B
for RHD
*a
Driver Side Curtain Shield Squib
*b
Center Airbag Sensor Assembly
*c
Driver Side Floor Wire
*d
Front view of wire harness connector
(to Driver Side Curtain Shield Squib)
*e
Connector C
|
|
||||
| OK | |
| 5. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the connectors to the driver side - curtain shield airbag assembly and the center airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1830/57, B1831/57, B1832/57 and B1833/57 are not output.
- HINT:
- DTCs other than DTC B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
