2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1835/58 Short in Curtain Shield Squib LH Circuit

Diagnostic trouble codes · Vehicles built from Aug 2012

Also covers:

DESCRIPTION

The curtain shield squib LH circuit consists of the center airbag sensor assembly and curtain shield airbag assembly LH.
The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1835/58
  1. The center airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit during primary check.
  2. Curtain shield squib LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Curtain shield airbag assembly LH (Curtain shield squib LH)
  3. Center airbag sensor assembly
B1836/58
  1. The center airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit.
  2. Curtain shield squib LH malfunction
  3. Center airbag sensor assembly malfunction
B1837/58
  1. The center airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH circuit.
  2. Curtain shield squib LH malfunction
  3. Center airbag sensor assembly malfunction
B1838/58
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit.
  2. Curtain shield squib LH malfunction
  3. Center airbag sensor assembly malfunction

WIRING DIAGRAM

C268593E02

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the curtain shield airbag assembly LH and center airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the curtain shield airbag assembly LH and center airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the No. 2 floor wire connector (on the curtain shield airbag assembly side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

  1. Check that the short spring for the No. 2 floor wire with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


2. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH
SST
09843-18061  

  1. C268596E03
    Connect the connector to the center airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the curtain shield airbag assembly LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting it.
    2. Insert SST straight into the terminals of the connector.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.

    HINT:
    Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect SST from connector C.

    Text in Illustration 
    *1
    Curtain Shield Airbag Assembly LH
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Curtain Shield Airbag Assembly LH)



NG
Go to step 3
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH (Click here)

3. CHECK NO. 2 FLOOR WIRE

  1. C268597E03
    Disconnect the No. 2 floor wire from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      L8-1 (ICL+) - Body ground
      Ignition switch ON
      Below 1 V
      L8-2 (ICL-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L8-1 (ICL+) - L8-2 (ICL-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L8-1 (ICL+) - Body ground
      Always
      1 MΩ or higher
      L8-2 (ICL-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L8-1 (ICL+) - L8-2 (ICL-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.

      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly LH
      *2
      Center Airbag Sensor Assembly
      *3
      No. 2 Floor Wire
      *a
      Front view of wire harness connector
      (to Curtain Shield Airbag Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


4. CHECK DTC

  1. C268592E03
    Connect the connectors to the curtain shield airbag assembly LH and center airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.

    HINT:
    Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Curtain Shield Airbag Assembly LH
    *2
    Center Airbag Sensor Assembly



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1830/57 Short in Driver Side Curtain Shield Squib Circuit (+ B1831/57, B1832/57, B1833/57) (Nov 2010 – Jul 2012)B1835/58 Short in Front Passenger Side Curtain Shield Squib Circuit (+ B1836/58, B1837/58, B1838/58) (Jul 2007 – Oct 2010) →