2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


CAN JUNCTION CONNECTOR

  1. CAN J/C connectors.

    HINT:
    1. The connectors connected to the CAN J/C can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. E62, E63, E64 and E65 are interchangeable.

    B125053E04
    Wiring color 
    CAN J/C connectors ("A" side, w/ earth terminal)
    Color (CAN-H Side)
    Color (CAN-L Side)
    ECM (E62)
    W
    R
    DLC3 (E63)
    P
    V
    Steering angle sensor (E64)
    B
    Y
    Yaw rate sensor (E65)
    L
    LG
    Wiring color 
    CAN J/C connectors ("B" side, w/o earth terminal)
    Color (CAN-H Side)
    Color (CAN-L Side)
    Skid control ECU (E66)
    B
    W

  2. C133723E01
    The terminals of the CAN J/C connectors.
    Terminal
    Terminal symbol
    1
    CAN-H
    2
    CAN-L

  3. G026214E15
    Measure the resistance.

    Standard resistance:
    Terminal
    Specified Condition
    CANH - CANL
    108 to 132 Ω

  4. Wiring diagram for identifying CAN J/C connectors.
    C133802E01


DLC3
G026206E72
  1. Turn the ignition switch OFF.

  2. Measure the resistance.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    E1-6 (CANH) - E1-14 (CANL)
    P - V
    Ignition Switch OFF
    54 to 69 Ω
    E1-6 (CANH) - E1-4 (CG)
    P - W-B
    Ignition Switch OFF
    200 Ω or more
    E1-14 (CANL) - E1-4 (CG)
    V - W-B
    Ignition Switch OFF
    200 Ω or more
    E1-6 (CANH) - E1-16 (BAT)
    P - O
    Ignition Switch OFF
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    V - O
    Ignition Switch OFF
    6k Ω or more


SKID CONTROL ECU
C132867E04
  1. Turn the ignition switch OFF.

  2. Disconnect the A4 skid control ECU connector.

  3. Measure the resistance.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    B - W
    Ignition Switch OFF
    54 to 69 Ω
    A4-11 (CANH) - A4-32 (GND2)
    B - W-B
    Ignition Switch OFF
    200 Ω or more
    A4-25 (CANL) - A4-32 (GND2)
    W - W-B
    Ignition Switch OFF
    200 Ω or more
    A4-11 (CANH) - A4-31 (+BS)
    B - Y
    Ignition Switch OFF
    6 kΩ or more
    A4-25 (CANL) - A4-31 (+BS)
    W - Y
    Ignition Switch OFF
    6 kΩ or more


ECM
C133767E01
  1. Turn the ignition switch OFF.

  2. Disconnect the B1, E46 and E47 ECM connectors.

  3. Measure the resistance.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    E46-33 (CANH) - E46-34 (CANL)
    W - R
    Ignition switch OFF
    108 to 132 Ω
    E46-33 (CANH) - B1-7 (E01)
    W - BR
    Ignition switch OFF
    200 Ω or more
    E46-34 (CANL) - B1-7 (E01)
    R - BR
    Ignition switch OFF
    200 Ω or more
    E46-33 (CANH) - E47-3 (BATT)
    W - L
    Ignition switch OFF
    6 kΩ or more
    E46-34 (CANL) - E47-3 (BATT)
    R - L
    Ignition switch OFF
    6 kΩ or more


YAW RATE SENSOR
C125958E06
  1. Turn the ignition switch OFF.

  2. Disconnect the E34 yaw rate sensor connector.

  3. Measure the resistance.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    E34-3 (CANH) - E34-2 (CANL)
    L - LG
    Ignition switch OFF
    54 to 69 Ω
    E34-3 (CANH) - E34-1 (GND)
    L - W-B
    Ignition switch OFF
    200 Ω or more
    E34-2 (CANL) - E34-1 (GND)
    LG - W-B
    Ignition switch OFF
    200 Ω or more
    E34-3 (CANH) - E1-16 (BAT)
    L - O
    Ignition switch OFF
    6 kΩ or more
    E34-2 (CANL) - E1-16 (BAT)
    LG - O
    Ignition switch OFF
    6 kΩ or more


STEERING ANGLE SENSOR
C133843E01
  1. Turn the ignition switch OFF.

  2. Disconnect the E16 steering angle sensor connector.

  3. Measure the resistance.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    E16-3 (CANH) - E16-11 (CANL)
    B - Y
    Ignition switch OFF
    54 to 69 Ω
    E16-3 (CANH) - E16-2 (ESS)
    B - W-B
    Ignition switch OFF
    200 Ω or more
    E16-11 (CANL) - E16-2 (ESS)
    Y - W-B
    Ignition switch OFF
    200 Ω or more
    E16-3 (CANH) - E16-9 (BAT)
    B - W-R
    Ignition switch OFF
    6 kΩ or more
    E16-11 (CANL) - E16-9 (BAT)
    Y - W-R
    Ignition switch OFF
    6 kΩ or more

← PROBLEM SYMPTOMS TABLE (from Aug 2012)TERMINALS OF ECU (Aug 2009 – Oct 2010) →