TERMINALS OF ECU
System information · Vehicles built Aug 2011 – Jul 2012
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012
- NOTICE:
- Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
- After the ignition switch is turned off, check that the key reminder warning system is not in operation.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
- Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
| CAN JUNCTION CONNECTOR NO. 1 (for LHD) |


| *a |
to ECM |
*b |
to Yaw Rate Sensor |
| *c |
to Combination Meter ECU |
*d |
to DLC3 |
| *e |
to Steering Angle Sensor |
*f |
to Skid Control ECU |
| *g |
to Airbag Sensor Assembly |
- |
- |
| Terminal No. (symbol) |
Wiring color |
Connect to |
| E95-1 (CANH) |
LG-R |
ECM |
| E95-12 (CANL) |
LG-B |
ECM |
| E95-2 (CANH) |
LG |
Yaw Rate Sensor |
| E95-13 (CANL) |
L |
Yaw Rate Sensor |
| E95-3 (CANH) |
R |
Combination Meter ECU |
| E95-14 (CANL) |
W |
Combination Meter ECU |
| E95-4 CANH) |
P |
DLC3 |
| E95-15 (CANL) |
V |
DLC3 |
| E95-5 (CANH) |
L |
Steering Angle Sensor |
| E95-16 (CANL) |
W |
Steering Angle Sensor |
| E95-6 (CANH) |
B |
Skid Control ECU |
| E95-17 (CANL) |
W |
Skid Control ECU |
| E95-7 (CANH) |
Y |
Airbag Sensor Assembly |
| E95-18 (CANL) |
W |
Airbag Sensor Assembly |
| CAN JUNCTION CONNECTOR NO. 1 (for RHD) |


| *a |
to ECM |
*b |
to Yaw Rate Sensor |
| *c |
to CAN Junction Connector No. 2 |
*d |
to Airbag Sensor Assembly |
| Terminal No. (symbol) |
Wiring color |
Connect to |
| E95-1 (CANH) |
LG-R |
ECM |
| E95-12 (CANL) |
LG-B |
ECM |
| E95-2 (CANH) |
LG |
Yaw Rate Sensor |
| E95-13 (CANL) |
L |
Yaw Rate Sensor |
| E95-3 (CANH) |
R |
CAN Junction Connector No. 2 |
| E95-14 (CANL) |
W |
CAN Junction Connector No. 2 |
| E95-7 (CANH) |
Y |
Airbag Sensor Assembly |
| E95-18 (CANL) |
W |
Airbag Sensor Assembly |
| CAN JUNCTION CONNECTOR NO. 2 (for RHD) |


| *a |
to Steering Angle Sensor |
*b |
to DLC3 |
| *c |
to CAN Junction Connector No. 3 |
*d |
to CAN Junction Connector No. 1 |
| Terminal No. (symbol) |
Wiring color |
Connect to |
| E92-1 (CANH) |
Y |
CAN Junction Connector No. 3 |
| E92-7 (CANL) |
W |
CAN Junction Connector No. 3 |
| E92-2 CANH) |
R |
CAN Junction Connector No. 1 |
| E92-8 (CANL) |
W |
CAN Junction Connector No. 1 |
| E91-5 (CANH) |
L |
Steering Angle Sensor |
| E91-11 (CANL) |
W |
Steering Angle Sensor |
| E91-6 (CANH) |
P |
DLC3 |
| E91-12 (CANL) |
V |
DLC3 |
| CAN JUNCTION CONNECTOR NO. 3 (for RHD) |


| *a |
to Skid Control ECU |
*b |
to Combination Meter ECU |
| *c |
to CAN Junction Connector No. 2 |
- |
- |
| Terminal No. (symbol) |
Wiring color |
Connect to |
| A43-1 (CANH) |
B |
Skid Control ECU |
| A43-12 (CANL) |
W |
Skid Control ECU |
| A43-2 (CANH) |
R |
Combination Meter ECU |
| A43-13 (CANL) |
W |
Combination Meter ECU |
| A43-3 (CANH) |
Y |
CAN Junction Connector No. 2 |
| A43-14 (CANL) |
W |
CAN Junction Connector No. 2 |
| DLC3 |
![]() ![]() |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
Text in Illustration *a
DLC3
Standard Resistance Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
E1-6 (CANH) - E1-14 (CANL)
P - V
Ignition switch off
54 to 69 Ω
E1-6 (CANH) - E1-4 (CG)
P - W-B
Ignition switch off
200 Ω or more
E1-14 (CANL) - E1-4 (CG)
V - W-B
Ignition switch off
200 Ω or more
E1-6 (CANH) - E1-16 (BAT)
P - B-R
Ignition switch off
6 kΩ or more
E1-14 (CANL) - E1-16 (BAT)
V - B-R
Ignition switch off
6 kΩ or more
| MASTER CYLINDER SOLENOID (SKID CONTROL ECU) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the A4 master cylinder solenoid (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
Text in Illustration *a
Front view of wire harness connector
(to Master Cylinder Solenoid (Skid Control ECU))
Standard Resistance Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
A4-11 (CANH) - A4-25 (CANL)
B - W
Ignition switch off
54 to 69 Ω
A4-11 (CANH) - A4-32 (GND2)
B - W-B
Ignition switch off
200 Ω or higher
A4-25 (CANL) - A4-32 (GND2)
W - W-B
Ignition switch off
200 Ω or higher
A4-11 (CANH) - A4-31 (+BS)
B - Y
Ignition switch off
6 kΩ or higher
A4-25 (CANL) - A4-31 (+BS)
W - Y
Ignition switch off
6 kΩ or higher
| ECM |


| *a |
Front view of wire harness connector (to ECM) |
- |
- |
Turn the ignition switch off.
Disconnect the E81, E82 and B50 ECM connectors.
Measure the resistance according to the value(s) in the table below.
Standard Resistance Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
E81-32 (CANH) - E81-31 (CANL)
LG-R - LG-B
Ignition switch off
108 to 132 Ω
E81-32 (CANH) - B50-14 (E01)
LG-R - BR
Ignition switch off
200 Ω or higher
E81-31 (CANL) - B50-14 (E01)
LG-B - BR
Ignition switch off
200 Ω or higher
E81-32 (CANH) - E82-24 (BATT)
LG-R - L
Ignition switch off
6 kΩ or higher
E81-31 (CANL) - E82-24 (BATT)
LG-B - L
Ignition switch off
6 kΩ or higher
| YAW RATE SENSOR |
![]() ![]() |
Turn the ignition switch off.
Disconnect the E83 yaw rate sensor connector.
Measure the resistance according to the value(s) in the table below.
Text in Illustration *a
Front view of wire harness connector
(to Yaw Rate Sensor)
*b
DLC3
Standard Resistance Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
E83-3 (CANH) - E83-2 (CANL)
LG - L
Ignition switch off
54 to 69 Ω
E83-3 (CANH) - E83-1 (GND)
LG - W-B
Ignition switch off
200 Ω or higher
E83-2 (CANL) - E83-1 (GND)
L - W-B
Ignition switch off
200 Ω or higher
E83-3 (CANH) - E1-16 (BAT)
LG - B-R
Ignition switch off
6 kΩ or higher
E83-2 (CANL) - E1-16 (BAT)
L - B-R
Ignition switch off
6 kΩ or higher
| STEERING ANGLE SENSOR |
![]() ![]() |
Turn the ignition switch off.
Disconnect the E16 steering angle sensor connector.
Measure the resistance according to the value(s) in the table below.
Text in Illustration *a
Front view of wire harness connector
(to Steering Sensor)
Standard Resistance Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
E16-3 (CANH) - E16-11 (CANL)
L - W
Ignition switch off
54 to 69 Ω
E16-3 (CANH) - E16-2 (ESS)
L - W-B
Ignition switch off
200 Ω or higher
E16-11 (CANL) - E16-2 (ESS)
W - W-B
Ignition switch off
200 Ω or higher
E16-3 (CANH) - E16-9 (BAT)
L - W-R
Ignition switch off
6 kΩ or higher
E16-11 (CANL) - E16-9 (BAT)
W - W-R
Ignition switch off
6 kΩ or higher
| COMBINATION METER ASSEMBLY (COMBINATION METER ECU) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the E13 and E14 combination meter assembly (combination meter ECU) connectors.
Measure the resistance according to the value(s) in the table below.
Text in Illustration *a
Front view of wire harness connector
(to Combination Meter Assembly (Combination Meter ECU))
Standard Resistance Terminal No. (symbol)
Wiring color
Switch Condition
Specified Condition
E14-10 (CANH) - E14-9 (CANL)
R - W
Ignition switch off
54 to 69 Ω
E14-10 (CANH) - E13-21 (ES)
R - W-B
Ignition switch off
200 Ω or higher
E14-9 (CANL) - E13-21 (ES)
W - W-B
Ignition switch off
200 Ω or higher
E14-10 (CANH) - E13-1 (B)
R - R
Ignition switch off
6 kΩ or higher
E14-9 (CANL) - E13-1 (B)
W - R
Ignition switch off
6 kΩ or higher
| AIRBAG SENSOR ASSEMBLY |
![]() ![]() |
Turn the ignition switch off.
Disconnect the E29 airbag sensor assembly.
Measure the resistance according to the value(s) in the table below.
Text in Illustration *a
Front view of wire harness connector
(to Airbag Sensor Assembly)
*b
DLC3
Standard Resistance Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
E29-13 (CANH) - E29-22 (CANL)
Y - B
Ignition switch off
54 to 69 Ω
E29-13 (CANH) - E1-4 (CG)
Y - W-B
Ignition switch off
200 Ω or higher
E29-22 (CANL) - E1-4 (CG)
B - W-B
Ignition switch off
200 Ω or higher
E29-13 (CANH) - E1-16 (BAT)
Y - B-R
Ignition switch off
6 kΩ or higher
E29-22 (CANL) - E1-16 (BAT)
B - B-R
Ignition switch off
6 kΩ or higher





